4OM-1011-002 - 第30页

0305-001 Tg0860-PM-MM 1-15 Fig. 4A20 Placement Head V acuum Filter Checking Remove the vacuum filter with the vacuum filter replacement jig (at- tached) and check for dirt. Replace the filter with a new one when it is st…

0305-001 Tg0860-PM-MM

1-14

Fig. 4A19 Vacuum Nozzle

6. Monthly Maintenance

Inside of Vacuum Nozzle

Cleaning

Blow air to the inside of the vacuum

nozzle.

Hole of Vacuum Nozzle

Cleaning

Blow air to the hole of the vacuum

nozzle.

Vacuum Nozzle End

Cleaning

Clean it with a rag.

Fig. 4A18 Nozzle Stocker

Nozzle Storage Section

Cleaning

Remove dirt and dust using a rag.

Cam Follower

Cleaning and Lubrication (NM1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Apply new grease with a brush,

etc.

Beam A Side

Beam B Side

Beam A Side

Beam B Side

Note: Sebum nor oil, etc., should not adhere to the surface of the diffusion plate.

Do not use a rag to wipe off dirt.

Refer to “1.7 Vacuum Nozzles of Section 2 in Volume 1” for details.

Diffusion

Plate

Note

0305-001 Tg0860-PM-MM

1-15

Fig. 4A20 Placement Head

Vacuum Filter

Checking

Remove the vacuum filter with the

vacuum filter replacement jig (at-

tached) and check for dirt.

Replace the filter with a new one

when it is stained excessively.

Refer to “2.2 Replacement Procedure

of Vacuum Filter” for details.

Beam A Side

Beam B Side

6. Monthly Maintenance

0305-001 Tg0860-PM-MM

7. Maintenance (Every 3 Months after Initial

Maintenance in 1 Month)

Notes: (a) Perform break-in after lubrication. After a proper break-in, wipe off

any dropped grease with an oiled rag.

(b) Grease Symbols

DE1 : DAPHNE EPONEX GREASE No.1

NM1 : NEW MOLYNOC GREASE No.1

1-16

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)

Maintenance Spots Check

Name

Fig.

No.

Description Grease

Cleaning

Tools,

Nozzles, etc.

Feeder Base Cam and Cam Follower 4A21 Lubrication

NM1

Brush or

Cloth

X-Axis Ball Screw

(2 nipples)

4A22 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

X-Axis Linear Guide

(8 nipples)

4A23 Cleaning and

Lubrication

DE1

Oiled rag,

H Type

Y-Axis Ball Screw 4A24 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

X/Y Beam

(Beams A and B)

Y-Axis Linear Guide

(8 nipples)

4A24 Cleaning and

Lubrication

DE1

SPK-3C,

U and P

Types,

Oiled rag

Placement Head Ball Screw and Nut

(4 nipples)

Linear Guide

4A25 Cleaning and

Lubrication DE1

U and

N Types,

Oiled rag

Large Linear Guide

(2 nipples)

4A26 Cleaning and

Lubrication

DE1

Oiled rag, N

and U Types

Small Linear Guide 4A26 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

Clamp Sections of

Tray Traverse

Cam Follower 4A26 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

CAUTION

The ball screws and linear guides have a high main-

tenance priority.

The initial maintenance should be performed in one

month. After that, it should be performed every three

months.

Table 4A8