4OM-1011-002 - 第33页

0305-001 Tg0860-PM-MM 1-18 Fig. 4A22 X/Y Beam (Beams A and B) X-Axis X-Axis Ball Screw Cleaning and Lubrication (DE1) (1) W ipe off old grease with an oiled rag. Note: T ake care not to leave any waste thread. (2) Lubric…

Tg0860-PM-MM

Beam A Side

Beam B Side

# #

Setscrews (10 places)

Fig. 4A21 Feeder Base

Cam and Cam Follower

Lubrication (NM1)

(1) Remove the setscrews (10 places)

and then remove the plate from

the side of the feeder base.

(2) Apply new grease with a brush, etc.

The cam and cam follower are lo-

cated in the depth of Arrow A.

Note: Lubricate it covering this

section with cloth, etc. to

avoid dropping grease

onto the wiring.

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)

0307-002 1-17

0305-001 Tg0860-PM-MM

1-18

Fig. 4A22 X/Y Beam (Beams A and B) X-Axis

X-Axis Ball Screw

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Lubricate the 2 nipples with new

grease from a grease gun.

Note: The attachments to be

used are SPK-3C, U type

and P type.

Fig. 4A23 X/Y Beam (Beams A and B) X-Axis

Beam A Side

Beam B Side

X-Axis Linear Guide

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Lubricate the 8 nipples with new

grease from a grease gun.

Note: The attachment to be

used is H type.

SPK-3C

U Type

P Type

Beam A Side

Beam B Side

Nipple

2 nipples

Nipple

H Type

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)

0305-001 Tg0860-PM-MM

1-19

Nipple

Fig. 4A24 X/Y Beam (Beams A and B) Y-Axis

Beam A Side

Beam B Side

Fig. 4A25 Placement Head

Y-Axis Ball Screw

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Apply new grease by hand or with

a brush.

Y-Axis Linear Guide

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Lubricate the 8 nipples with new

grease from a grease gun.

Note: The attachments to be

used are SPK-3C, U

type and P type.

SPK-3C

U Type

P Type

Ball Screw and Linear Guide

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Lubricate the 4 nipples with new

grease from a grease gun.

Notes: (a) For the lubrication

procedure, refer to

“10.1 Placement

Head and PCB Posi-

tioning Section”.

(b) The attachments to

be used are U type

and N type.

U Type

N Type

Nipple

Beam A Side

Beam B Side

Nipple

2 nipples

Nipple

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)