DEK INFINITY USER MANUAL - 第22页
INFINITY 0$&+,1( 352*5$ 00,1* 67$*( (',7 $352'8&7 ),/( 1.20 User Manual Software Versi on 7 5. Use either the Incr . and Decr . keys (F6 - F7) or the forward slash key (/) on the keyboard to ch…
INFINITY
0$&+,1(352*5$00,1*
67$*((',7$352'8&7),/(
Software Version 7 User Manual 1.19
STAGE 3 - EDIT A PRODUCT FILE
1. Select Edit Data (F3).
The following Edit Current Process Parameters window is displayed:
2. Select Incr. (F6). Type in the required product name and press Enter using
the keyboard.
3. Highlight Product ID using the Next key (F4). Select Incr. (F6). Type in
the required product ID and press Enter using the keyboard.
NOTE
If 2D Inspection is enabled and the product file being copied has an assigned
inspection file, the user is prompted to make a copy of the file. (See 2Di
Setup in 2Di Inspection chapter later in this manual.)
4. Use the Next and Previous keys (F4 - F5) to highlight the relevant parameter.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
PRODUCT NAME
PRODUCT ID
DWELL HEIGHT
DWELL SPEED
SCREEN ADAPTOR
SCREEN IMAGE
CUSTOM SCREEN
BOARD WIDTH
BOARD LENGTH
BOARD THICKNESS
FRONT PRINT SPEED
REAR PRINT SPEED
FLOOD SPEED
PRINT FRONT LIMIT
Dek04
Dek04
30
24
NONE
EDGE
DISABLED
101.5
152.5
1.6
150
150
20
0.0
mm
mm/s
mm
mm
mm
mm/s
mm/s
mm/s
mm
.. more
Edit Current Process Parameters
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
INFINITY
0$&+,1(352*5$00,1*
67$*((',7$352'8&7),/(
1.20 User Manual Software Version 7
5. Use either the Incr. and Decr. keys (F6 - F7) or the forward slash key (/) on
the keyboard to change the parameter value.
NOTE
A definition of all editable parameters is contained at the end of this chapter.
6. Select Save (F2). The message ‘Saving fiducial data - Please wait Board
data file saved’ is displayed.
7. Repeat Steps 4 - 6 for the remaining parameters.
8. Select Exit (F8).
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
INFINITY
0$&+,1(352*5$00,1*
67$*($),7648((*((6
Software Version 7 User Manual 1.21
STAGE 4A - FIT SQUEEGEES
If ProFlow was used when running the last product, carry out the ProFlow to
Squeegee Replacement Procedure, (Squeegee Module Chapter - Replacement
Procedures of Technical Reference Manual refers).
1. Select Setup (F6).
2. Select Setup Squeegee (F4).
3. Select Change Squeegee (F1).
4. Lift the front printhead cover.
5. Before fitting the squeegees to the machine, fix the paste deflectors to each
end of the squeegee assemblies, using the screws supplied. Ensure that the
bottom edge of the deflector is above the lower edge of the squeegee blade.
The setting of the paste deflectors is carried out later in this chapter.
NOTE
The deflectors are handed so care must be taken to fix the correct deflector
to each end of the squeegee assemblies.
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Change
Squeegee
Calibrat
Heights
Exit