DEK INFINITY USER MANUAL - 第347页

INFINITY &21680$ %/(5( 3/(1,6+0(1 76 352)/2: Soft ware Ver sion 7 User Manual 9.63 16. Se lect Run (F1). If the Camera Idle Position in Set Prefe rences is set to Be hind Rail, the following window and menu bar is d…

100%1 / 356
INFINITY
&21680$%/(5(3/(1,6+0(176
352)/2:
9.62 User Manual Software Version 7
6. If the set preference is set to pause, the tricoloured beacon shows red and the
following window is displayed:
7. If the ProFlow unit is in front of the image continue with Step 8. If the
ProFlow unit is at the rear of the image go to Step 9.
8. Select Defer (F8). The machine carries out a print cycle, the ProFlow unit
moves to the rear of the image and the pause on warning window is re-
displayed.
9. Select Refill Paste (F1). The message ‘Open the cover and change the
ProFlow cassette.’ is displayed.
10.Select Open Cover (F2).
11. Carry out Steps 23-34 of Prior to a Print Run procedure, earlier in this
section.
12.Select Continue (F1). The print run resumes.
13.If the set preference is set to suspend, the tricoloured beacon shows red and
the following window is displayed:
14.If the ProFlow unit is in front of the image continue with Step 15. If the
ProFlow unit is at the rear of the image go to Step 17.
15.Select End Run (F8).
Pause on Warning
Print Medium Low. Please replenish.
Refill
Paste
Defer
Refill
Paste
Defer
Continue
Open
Cover
Continue
Open
Cover
Suspend on Warning
Print Medium Low. Please replenish.
Refill
Paste
End
Run
INFINITY
&21680$%/(5(3/(1,6+0(176
352)/2:
Software Version 7 User Manual 9.63
16.Select Run (F1).
If the Camera Idle Position in Set Preferences is set to Behind Rail, the
following window and menu bar is displayed:
Selecting Continue Run clears the warning window and the print cycle
continues.
Selecting End Run clears the warning window, the print cycle is aborted and
control is returned to the ready page.
If the Unload Board Start in Set Preferences is set to Separation, the follow-
ing window and menu bar is displayed:
Selecting Continue Run clears the warning window and the print cycle
continues.
Selecting End Run clears the warning window, the print cycle is aborted and
control is returned to the ready page.
NOTE
If Camera Idle Position is set to Behind Rail and Unload Board Start is set
to Separation, the warning windows appear one after the other in the order
shown above.
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Camera Behind Rail Warning
The CAMERA HOME POSITION is set to 'Behind
Rail'
Ensure that no tooling pins or other
obstructions are on the table behind the
rear rail, as these could cause damage to
the camera.
This option will only have an effect for
boards that are less than 250mm wide.
This option can be disabled from the set
preference page.
Continue
Run
End
Run
Unload Board Speedup Warning
The UNLOAD BOARD SPEEDUP option is set to
'Separation'
With this option enabled it should be noted
that there is only a minimal clearance
between the underside of the board and any
tooling being used, while the board is being
unloaded.
This option must not be used for boards that
are populated on the underside, as this
could damage the boards.
Continue
Run
End
Run
INFINITY
&21680$%/(5(3/(1,6+0(176
352)/2:
9.64 User Manual Software Version 7
The print run resumes. The machine carries out a print cycle, the ProFlow
unit moves to the rear of the image and the suspend on warning window is
re-displayed.
17.Select Refill Paste (F1). The message ‘Open the cover and change the
ProFlow cassette.’ is displayed.
18.Select Open Cover (F2).
19.Carry out Steps 23-34 of Prior to a Print Run procedure, earlier in this
section.
20.Select Continue (F1). The print run resumes.
Refill
Paste
End
Run
Continue
Open
Cover
Continue
Open
Cover