DEK INFINITY USER MANUAL - 第97页

INFINITY 0$&+,1 (352*5 $00,1* 0(18 3$5$ 0(7 (56 Soft ware Ver sion 7 User Manual 1.95 Pr oFlow Knead Pr essure This parameter sets the pressure to be applied, while using P roFlow , when kneading in either directio…

100%1 / 356
INFINITY
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.94 User Manual Software Version 7
Rear Print Speed This parameter sets the speed across the screen when printing.
Flood Speed This Parameter sets the flood blade speed across the screen when performing a
flood stroke.
Print Front Limit This determines the distance from the front edge of the board that printing must
start.
NOTE
With Paste Trails enabled or ProFlow fitted the minimum value is 0mm.
Print Rear Limit This determines the distance from the rear edge of the board that printing must
start.
NOTE
With Paste Trails enabled or ProFlow fitted the minimum value is 0mm.
Front Pressure This parameter sets the force applied by the front squeegee during its print
stroke.
Rear Pressure This parameter sets the force applied by the rear squeegee during its print stroke.
Flood Height This parameter sets the height of the flood blade above the screen during a flood
stroke.
Minimum Maximum Increment Default
2.0mm/sec 150.0mm/sec 1.0mm/sec 10.0mm/sec
Minimum Maximum Increment
10.0mm/sec 150.0mm/sec 1.0mm/sec
Minimum Maximum Increment Default
-6.5mm Board Width - print rear limit 0.1mm 0.0mm
Minimum Maximum Increment Default
-6.5mm Board Width - print front limit 0.1mm 0.0mm
Minimum Maximum Increment
0.0Kg 20.0Kg 0.2Kg
Minimum Maximum Increment
0.0Kg 20.0Kg 0.2Kg
Minimum Maximum Increment
0.0mm 5.0mm 0.02mm
INFINITY
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 7 User Manual 1.95
ProFlow Knead
Pressure
This parameter sets the pressure to be applied, while using ProFlow, when
kneading in either direction.
Knead Off-image This parameter sets whether ProFlow is to knead in an off-image area of the
stencil. Options are:
Knead Before
Printing
This parameter sets ProFlow to knead before printing the first board and the
amount of boards to be printed between kneading.
NOTE
This parameter is only displayed if Knead Off-image is set to enabled.
Stencil Protection This parameter sets whether tooling to support the stencil, outside the board and
clamp envelopes, is in use. Options are:
NOTE
This parameter is only displayed while ProFlow is fitted.
Print Gap This parameter sets the gap required between the screen and board to be printed
during the print stroke.
Underside
Clearance
This parameter determines the clearance provided between the underside of the
board and the top of the machine tooling to allow for components on the
underside of the board.
Minimum Maximum Increment Default
0.0Kg 20.0Kg 0.2Kg 10.0Kg
Options Available Default
Enabled Enabled
Disabled
Minimum Maximum Increment Default
0
(disables knead before printing)
100 1 0
Options Available Default
On On
Off
Minimum Maximum Increment
0.0mm 6.0mm 0.025mm
Minimum Maximum Increment Default
3.0mm 42.0mm 0.1mm 19.0mm
INFINITY
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.96 User Manual Software Version 7
Separation Speed This parameter sets the speed at which the rising table drives down the separa-
tion distance.
Separation
Distance
This parameter sets the separation distance between board and screen. The
parameter can help increase cycle time when a low separation speed is used by
decreasing the separation distance.
Board Count This function provides the facility for the print cycle to be halted automatically
on a board count basis.
If the board stop count is zero this function is not active. When a print run is
started, a count is made from the STOP CYCLE AFTER value to zero decre-
menting by one for each board printed.
When the counter reaches zero, the print cycle is finished and control returned
to the main display page and the beacon is set to amber, thus indicating that the
machine requires operator attention.
The operator has access to all of the machines options. Once the operator has
performed any required operations, the run button can be pressed to continue the
print cycle.
Separation Delay This parameter is the time in seconds that the table delays before lowering. This
delay occurs during screen cleaning and after the flood. This parameter only
becomes available when Adhesive has been selected in the Print Mode
parameter.
Print Mode This parameter sets the mode of operation of the machine. Available modes are:
Minimum Maximum Increment
0.1mm/sec 20.0mm/sec 0.1mm/sec
Minimum Maximum Increment Default
0.0mm 3.0mm 0.1mm 3.0mm
Minimum Maximum Increment
0 Boards 500 Boards 1 Board
Modes Available Note Default
Print / Print Print / Print
Print / Flood
Flood / Print
Adhesive Selecting Adhesive from this parameter
opens the separation delay and print vacuum
mode