DEK INFINITY USER MANUAL - 第98页
INFINITY 0$&+,1( 352*5$ 00,1* 0(183$5$ 0(7(5 6 1.96 User Manual Software Versi on 7 Separ ation S peed This para meter set s the speed at whic h the ri sing table drives d own the separa- tion distance. Separ ation…
INFINITY
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 7 User Manual 1.95
ProFlow Knead
Pressure
This parameter sets the pressure to be applied, while using ProFlow, when
kneading in either direction.
Knead Off-image This parameter sets whether ProFlow is to knead in an off-image area of the
stencil. Options are:
Knead Before
Printing
This parameter sets ProFlow to knead before printing the first board and the
amount of boards to be printed between kneading.
NOTE
This parameter is only displayed if Knead Off-image is set to enabled.
Stencil Protection This parameter sets whether tooling to support the stencil, outside the board and
clamp envelopes, is in use. Options are:
NOTE
This parameter is only displayed while ProFlow is fitted.
Print Gap This parameter sets the gap required between the screen and board to be printed
during the print stroke.
Underside
Clearance
This parameter determines the clearance provided between the underside of the
board and the top of the machine tooling to allow for components on the
underside of the board.
Minimum Maximum Increment Default
0.0Kg 20.0Kg 0.2Kg 10.0Kg
Options Available Default
Enabled Enabled
Disabled
Minimum Maximum Increment Default
0
(disables knead before printing)
100 1 0
Options Available Default
On On
Off
Minimum Maximum Increment
0.0mm 6.0mm 0.025mm
Minimum Maximum Increment Default
3.0mm 42.0mm 0.1mm 19.0mm
INFINITY
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.96 User Manual Software Version 7
Separation Speed This parameter sets the speed at which the rising table drives down the separa-
tion distance.
Separation
Distance
This parameter sets the separation distance between board and screen. The
parameter can help increase cycle time when a low separation speed is used by
decreasing the separation distance.
Board Count This function provides the facility for the print cycle to be halted automatically
on a board count basis.
If the board stop count is zero this function is not active. When a print run is
started, a count is made from the STOP CYCLE AFTER value to zero decre-
menting by one for each board printed.
When the counter reaches zero, the print cycle is finished and control returned
to the main display page and the beacon is set to amber, thus indicating that the
machine requires operator attention.
The operator has access to all of the machines options. Once the operator has
performed any required operations, the run button can be pressed to continue the
print cycle.
Separation Delay This parameter is the time in seconds that the table delays before lowering. This
delay occurs during screen cleaning and after the flood. This parameter only
becomes available when Adhesive has been selected in the Print Mode
parameter.
Print Mode This parameter sets the mode of operation of the machine. Available modes are:
Minimum Maximum Increment
0.1mm/sec 20.0mm/sec 0.1mm/sec
Minimum Maximum Increment Default
0.0mm 3.0mm 0.1mm 3.0mm
Minimum Maximum Increment
0 Boards 500 Boards 1 Board
Modes Available Note Default
Print / Print Print / Print
Print / Flood
Flood / Print
Adhesive Selecting Adhesive from this parameter
opens the separation delay and print vacuum
mode
INFINITY
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 7 User Manual 1.97
Paste Ridge
Removal
This parameter enables the cleaning option Paste Ridge Removal. This option
removes the ridge of paste that can develop on the underside of the screen at the
end of the under screen cleaner stroke. Options are:
Print Deposits This parameter sets the number of consecutive print strokes carried out on one
substrate.
Print Vacuum
Mode
This parameter determines the state of the vacuum during the print and flood
stages of the cycle. The parameter is only available if Adhesive has been selected
in the Print Mode parameter.
Paste Dispense
Rate
This parameter sets the number of print cycles which occur between cycling of
the paste dispense system.
Paste Dispense
Speed
This parameter sets the speed at which the paste dispenser moves across the
screen thereby determining the amount of paste deposited on the screen.
Paste While Clean This parameter enables the machine to carry out a paste dispense while cleaning
the screen. Available modes are:
Option Default
Disabled Disabled
Enabled
Select Default
11
2
3
Mode
ON
OFF
Minimum Maximum Increment
0 (Dispenser switched off) 100 1
Minimum Maximum Increment
10.0mm/sec 100.0mm/sec 1.0mm/sec
Mode
Disabled
Mode 1
Mode 2
Both Modes