CP7 training(6.0) (1).pdf - 第83页
FK-9F98-27 CP-7 Series T raining T ext for Service Engineers Edition 6.0 Chapter 5. Loader and Con veyor Adjustment [15/28] 5.18 Loader System Sensor Positions 1. Refer to Fig. 27 for sensor locations a long the loader s…
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 5. Loader and Conveyor Adjustment [14/28]
5. Raise the lifter when the carrier claw clamps the board.
Set a dial gauge on the board as illustrated (two gauges are recommended) Since the dial
gauge cannot normally read 1.2mm, use a 1mm feeler gauge when setting up the dial gauge
before raising the lifter. (Set 1 end first, then the other)
When the lifter is raised, the dial gauge should read 0.2mm +/-0.1mm. If out of tolerance, adjust
the four bolts as indicated.
After adjustment, the lifter should raise the Pcb off the carrier claws by 1.2mm.
0 (using 1mm feeler gauge)
0.2 +/- 0.1 (when lifter is raised)
<Lifter Up>
<Lifter Down>
1.20mm
Figure 25
Upper end adjustment bolt (x 4)
Figure 26
.
6. For the lifter cylinder sensors, turn both the up and down end sensors ON first. Set the sensors
at a position 0.5mm further in towards the ON position.
<I/O → Standard → IN>
X0B5 In-Lifter Upper limit Check X0D0 Out-Lifter Upper Limit Check
X0B6 In-Lifter Lower Limit Check X0D1 Out-Lifter Lower Limit Check
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
5-14
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 5. Loader and Conveyor Adjustment [15/28]
5.18 Loader System Sensor Positions
1. Refer to Fig. 27 for sensor locations along the loader system.
2
1
3
2
3
1
2
2
3
3
<Carrier at retract position>
<IN Carrier>
<Carrier at advance position>
2
2
2
2
3
3
3
3
4
4
<OUT Carrier>
Figure 27
<Carrier Sensors>
1. Carrier retract end sensor 3.Carrier claw close- end sensor
2. Carrier claw open-end sensor 4. Carrier advance end sensor
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
5-15
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 5. Loader and Conveyor Adjustment [16/28]
5.19 Advance / Retract End Sensor Adjustment
1. Adjust the Advance and Retract End sensor height so the clearance between the top of the
sensor and dog is 1mm.
2. Align the center of the sensor with the dog in the X and Y directions.
<I/O → Standard → IN>
1mm
Figure 28
X0B3 In-carrier Forward Limit Check X0CE Out-carrier Forward Limit Check
X0B4 In-carrier Retract Limit Check X0CF Out-carrier Retract Limit Check
5.20 Claw Closed-End Sensor Adjustment
1. Close the carrier claws to turn the sensor ON. Move the sensor 1mm toward the ON position and
secure.
2. Align the center of the sensor with the dog in the X- direction.
As for the height, be careful to avoid any interference with the flag and sensor when opening and
closing the carrier claws.
Figure 29
<I/O → Standard → IN>
X0B7 In-carrier Retract Limit Clamp Check (Fixed Rail)
X0B8 In-carrier Retract Limit Clamp Check (Adjustable Rail)
X0B9 In-carrier Forward Limit Clamp Check (Fixed Rail)
X0BA In-carrier Forward Limit Clamp Check (Adjustable Rail)
X0D2 Out-carrier Retract Limit Clamp Check (Fixed Rail)
X0D3 Out-carrier Retract Limit Clamp Check (Adjustable Rail)
X0D4 Out-carrier Forward Limit Clamp Check (Fixed Rail)
X0D5 Out-carrier Forward Limit Clamp Check (Adjustable Rail)
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
5-16