SIPLACE DX4-Spec-设备性能参数-EN-DMS - 第18页
18 PCB Conveyor I-Placement Alternating Placement Mode Alternating or I-Placement mode Distance of outer conveyor edges: 680 mm, 2 lanes, outer conveyor edges fixed Alternating or I-Placement mode Distance of outer conve…
17
PCB Conveyor
Technical Data
Single Conveyor Flexible dual con-
veyor
Dual conveyor in sin-
gle conveyor mode-
Board dimensions
(length x width
a
)
Standard:
a) When using boards with a width > 450 mm, make sure the peripheral module can also process the PCB width
concerned.
50 mm x 50 mm to
285 mm x 560 mm
50 mm x 50 mm to
285mm x 325mm
50 mm x 50 mm to
285 mm x 560 mm
Option: “Long Board 380
b
b) "Long Board" option with restrictions.
50 mm x 50 mm to
380 mm x 560 mm
50 mm x 50 mm to
450mm x 325mm
50 mm x 50 mm to
450 mm x 560 mm
Option: “Long Board 550
b
50 mm x 50 mm to
550 mm x 560 mm
-- --
Stationary conveyor side Right or left Right, left or outer
Automatic electrical width
adjustment-
Yes
PCB thickness
Standard: 0.3 mm to 4.5 mm
PCB warpage see page 19
PCB weight
c
Standard
c) The board weight value refers to the weight of the board plus the weight of the components.
max. 2.0 kg max. 1.0 kg max. 2.0 kg
Clearance on PCB underside
Standard stopper:
Up to 25 mm
PCB transport height
Option:
Standard:
SMEMA option:
900 mm
930 mm
950 mm
Type of interface:
Standard:
Option:
SMEMA
Siemens
Component-free PCB handling
edge
3 mm
PCB changeover time
Single Conveyor
Dual conveyor
d
d) 0 seconds in asynchronous mode, otherwise 1.5 seconds.
< 1.5 seconds
0 seconds
Important information for machines in combination with SIPLACE DX4
When setting up a machine (D-, S-; F, HS, HF, X or SX series) next to a SIPLACE DX4, take note of the limited space
between the two machines. In these cases, a suitable conveyor extension is needed to create an operating space of
0.5 m between the machines.
18
PCB Conveyor
I-Placement
Alternating Placement Mode
Alternating or
I-Placement mode
Distance of outer conveyor
edges: 680 mm, 2 lanes, outer
conveyor edges fixed
Alternating or I-Placement
mode
Distance of outer conveyor
edges: 560 mm, 2 lanes, outer
conveyor edges fixed
Alternating placement mode
Distance of outer conveyor
edges: 535 mm, 2 lanes, right
conveyor edges fixed
a
Alternating placement mode
Distance of outer conveyor
edges: 601 mm, dual conveyor
in single conveyor mode, right
conveyor edge fixed
a
max. 325
Movable conveyor side
Stationary conveyor side
Only the settings with fixed conveyor edge on the right are shown. A setting with the stationary conveyor edge on the left is also
possible. All dimensions in millimeters.
max. 325
344 ± 17.5
680 (27“)
min. 35
max. 262
281 ± 17.5
560 (22“)
min. 35
max. 262
- 344
+ 258
max. 250
268 ± 18
min. 35
max. 250
535 (21“)
max. 601
19
PCB Warpage
PCB warpage across the direction of travel
max. 1 % of the PCB diagonal, but not
exceeding 2 mm
PCB warpage on the conveyor
PCB warpage during placement
PCB transport direction
PCB warpage downwards max. 0.5 mm
Use the magnetic pin supports, to achieve
this value.
Conveyor belt
Fixed clamped edge
PCB warpage in direction of travel
+ PCB thickness < 5.5 mm
Fixed clamped edge
Movable clamping device
When there is warpage under 2 mm, the
inkspots in the center of the board are also
within the focus of the digital camera. When
all the tolerances are taken into account,
this value is reduced to 1.5 mm.
You should also note that the warpage
reduces the component height.
Magnetic pin support
PCB