JO-109-002_JG-0209.pdf - 第65页
3-13 JO-109 1005-001 4. "T ype Setting" Window Feeder Parameter File (Before Measurement) Feeder Parameter File (After Measurement) In order to apply the control parameter data written in the feeder to the feed…
3-12
JO-109
1106-002
4. "Type Setting" Window
# of Components per Sprocket Circle
Specify the number of components (pickup holes) per sprocket circle. A
value "1 to 500" can be set.
Ref.:
The set number of components are used for graphical display.
Component Pitch (mm)
Specify the component (pickup hole) pitch in "mm".
A value "0.001 to 64.000" can be set.
Ref.:
The set value is used for graphical display.
Lot Data Input Omission Flag (0 or 1)
The set ag is used to omit the entry of lot data when the inspection is
executed.
0:
Not Omitted (Displayed and Specied at Each Inspection)
1:
Omitted (Only Displayed Initially and Omitted after Specication)
Fiducial Mark Positions X and Y
Specify the positional coordinates of the ducial mar according to the
position based on Master Reference Position 1.
Sprocket Feed Basic Pitch Y
Specify the tape feeding pitch per sprocket pin.
(Sprocket Feeding Distance at Transfer of Number of Divided Pulses on
Next Item)
A value "0.001 to 8.000" can be set.
# of Divided Pulses for Origin Offset Adjustment
The entry range of origin offset must also be specied here.
The offset value for adjustment is calculated based on an error between
the specied value and the feed basic pitch
A value "1 to 16384" can be set.
# of Measured Pickup Holes (1 or 2)
Specify the number of pickup hole rows (lanes).
A value "1" or "2" can be set.
Measured Pickup Hole Position #1 X and Y/Measured Pickup
Hole Position #2 X and Y
Specify the pickup hole inspection position according to the position
based on Master Reference Position 1.
When the number of rows (previous item) is "1", no parameter can be
specied for Pickup Hole Position 2.
3-13
JO-109
1005-001
4. "Type Setting" Window
Feeder Parameter File (Before Measurement)
Feeder Parameter File (After Measurement)
In order to apply the control parameter data written in the feeder to
the feeder adjusting jig environment, the feeder parameter le (before
measurement) is designated, where the data to be changed or modied
temporarily before the measurement, has been setup. Then, the feeder
parameter le (after measurement) is designated, where the data to
be returned to the set value when the adjusting jig measurement is
completed, has been setup.
The dedicated le is allocated in advance based on the type program.
Notice
Do not change the le designation.
If so, the measurement is not available.
3-14
JO-109
1106-002
4. "Type Setting" Window
(2) Details of Type Data
Type Name Type ID Nos.
This represents the regulated ID No. for type display regulation in the
"Type Listup" window.
The regulated ID Nos. are classied in the external le of the related
data. When the program is executed, the contents of this le is read and
registered in the regulation list box in the "Type Listup" window.
Inspection Type No.
Specify the number which represents the contents (method) of accuracy
inspection.
•
1: Inspection of Lane Origin Offset Adjustment
The origin offset position is inspected based on the design value
(position) of the target pickup hole.
The value is measured only in the Y-axis direction.
When the initial pickup hole is not located in the image processing
area, the position is shifted in the Y direction as much as the "Camera
Correction Pitch" specied in the system setting data.
The inspection position is moved to the place where the image
processing become possible.
As a result, the offset value for adjustment is calculated according
to the "CENTER" value (center value between "MAX." and "MIN."
values).
•
2: Inspection of Fiducial Mark Position Adjustment
An inspection is made to correct the pickup hole dislocated from the
ducial mark position.
The conrmation is made through the image processing of the
ducial mark before the pickup mark is inspected and he deviation
from the design value is stored in memory.
The pickup hole is inspected at the position where the pickup hole is
corrected as much as the shifted distance of the ducial mark.
The result of the measurement through the image processing of the
X and Y axes will be the result of correction equivalent to the shifted
distance of the ducial mark.
The result is displayed and "MAX.", "MIN.", "RANGE", and
"CENTER" values are displayed for each lane as the nal result.
Based on the "CENTER" value for each row (displayed here), the
value for feeder adjustment must be specied.