80S-2080F480F5 - 第41页
SIPLACE 80S-20/F4/F5 User M anual 1 Operational Safety 05/99 Issue from Software Version SR.405.xx 1.1 Information on safety 1 - 3 1.1 Information on safety 1.1.1 Convention for the use of d anger symbols These op eratin…
1 Operational Safety SIPLACE 80S-20/F4/F5 User Manual
05/99 Issue from Software Version SR.405.xx
1 - 2
SIPLACE 80S-20/F4/F5 User Manual 1 Operational Safety
05/99 Issue from Software Version SR.405.xx 1.1 Information on safety
1 - 3
1.1 Information on safety
1.1.1 Convention for the use of danger symbols
These operating instructions contain notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. The notes are highlighted by warning triangles and are indicated as follows
according to the level of risk:
DANGER or
within the intention of this user’s manual means that serious injury, death or considerable damage to property
will result
if the notes relating to danger are not observed.
WARNING or
within the intention of this user’s manual means that serious injury, death or considerable damage to property
could result
if the warning notes are not observed.
CAUTION or
within the intention of this user’s manual means that light injury or damage to property can result if the caution
notes are not observed.
NOTE
within the intention of this user’s manual provides important information concerning the product or that part of
the user’s manual to which particular attention is to be drawn.
1.1.2 Qualified personnel
Qualified or adequately trained personnel means that these people are familiar with the setting up, operation
and maintenance of automatic placement systems and add-on devices and have an appropriate qualification,
such as:
- Training or instruction or authorization to switch on or off, isolate, ground or label circuits and parts of the
installation in accordance with safety standards.
- Training or instruction in accordance with safety standards in the care and use of appropriate safety equip-
ment.
- Training in first aid.
1 Operational Safety SIPLACE 80S-20/F4/F5 User Manual
1.1 Information on safety 05/99 Issue from Software Version SR.405.xx
1 - 4
1.1.3 Use as prescribed
WARNING
The product must only be used for the applications specified in the catalogs and technical descriptions, and
then only in conjunction with non-Siemens devices and components that have been approved by Siemens.
For the product to operate correctly and reliably, it must have been transported, stored, erected and assembled
correctly and must be operated and maintained with care.
1.1.4 Important notes on operational safety
WARNING
In order to assure operational safety the following points must be observed without fail:
- NEVER open one of the two protective covers if you are not totally familiar with the sequence and function-
ing of the machine. Do not open the protective covers during operation unless you are told to do so in this
User Manual or in the station software dialog.
- Only trained and qualified personnel may set the key switch to set-up mode ("I").
- During operation, do not set the key switch to the "I" position (set-up mode) unless prompted to do so in
this manual or by the station software.Never bring your head or arms into the travel area of the gantry
when a station is switched on!
- No modifications of any type whatsoever may be made where it is not absolutely clear what effect they
would have on the functioning of the unit as a whole!
- The stations may only be adjusted, converted or maintained by personnel trained in this!
- Only use original spare parts and authorized accessories from Siemens AG. Using other parts will impair
safety and may cancel any liability of Siemens AG for the consequences.
- The operating safety of the SMD placement machines can only be guaranteed when the SMD placement
machines are used properly and for the purpose intended and when the provisions of the user’s manual
are complied with.
- The key for opening control and servo unit doors and the key for the key switch should be kept in a place
that is only accessible to qualified personnel.
- If it is necessary to work on the machine and you do not have enough trained personnel available in your
plant, always call in a service technician from Siemens AG. Siemens AG will not accept any claims for
damage or consequential damage that is the result of incorrect work.
- Machine operators must only carry out work for which they have been adequately trained and with which
they are totally familiar.
- You must also follow any special safety regulations applicable in your own country.
- Protective devices must NOT be modified. In particular, circuit-breakers must never be by-passed and pro-
tective devices must never be removed.
- If particular hazards are identified while the machine is in use, the machine operator must immediately
notify the manufacturer in writing so that the manufacturer can take appropriate action to minimise the
potential danger.