80S-2080F480F5 - 第415页
SIPLACE 80S-20/F4/F5 User M anual 6 What should you d o ... ? 05/99 Issue from Software Vers ion SR.405.xx 6.2 When you sw itch off the SIPLACE line 6 - 7 6.2.2 Switching off the st ations AT T E N T I O N When an automa…
6 What should you do ... ? SIPLACE 80S-20/F4/F5 User Manual
6.2 When you switch off the SIPLACE line 05/99 Issue from Software Version SR.405.xx
6 - 6
6.2 When you switch off the SIPLACE line
ATTENTION
Before you switch off the line ALWAYS make sure that:
– All the placement and gluing operations at the stations have ended.
– The z-axes of all placement and adhesive heads are in the top end position.
– None of the placement heads still contain components.
– All of the gantries have moved into the standby position.
– The station computers are shut down safely.
6.2.1 Switching off the line computer
CAUTION
NEVER just switch the line computer off at the power switch.
ALWAYS shut down the operating system. Otherwise you will almost certainly lose a lot of data or corrupt the
programs and you may have to reinstall the line computer software.
Position the mouse at the top or bottom right edge of the screen. The cursor will change into a cross.
Hold down the left mouse button. The main menu will appear on screen.
Move the mouse cursor onto ’Shutdown’ and then release the mouse button. The following dialog box will
appear on screen:
Click on ’Yes’. The dialog box will close and the software will shut down. This operation takes around 1
minute.The following box will then appear:
Switch off the UPS and monitor.
Shut down the computer
Yes No
Safe to Power Off
Press any key to reboot
SIPLACE 80S-20/F4/F5 User Manual 6 What should you do ... ?
05/99 Issue from Software Version SR.405.xx 6.2 When you switch off the SIPLACE line
6 - 7
6.2.2 Switching off the stations
ATTENTION
When an automatic placement system is in use, NEVER just power it off at the main switch (apart from in an emer-
gency).
The station computer runs under the WINDOWS NT operating system. You must shut down the operating
system correctly before switching off the station. The procedure for switching off the station is as follows:
End all placement and gluing operations.
Check that the z axes of all placement and glue application heads are in their top end position.
Check whether there are still components on the placement heads.
Move all gantries into the standby position.
Click on the ’Shut down computer’ option in the ’Operation’ menu.
This will end all the processes running on the station computer. A prompt will then appear on screen, telling
you that you can safely switch off the computer.
You can now switch off the placement system at the main switch.
PLEASE NOTE:
If you switch off the placement system while it is in use without first correctly shutting down the station com-
puter, the computer might not start again the next time you start up the line.
6 What should you do ... ? SIPLACE 80S-20/F4/F5 User Manual
6.3 When you change the job 05/99 Issue from Software Version SR.405.xx
6 - 8
6.3 When you change the job
Stop the placement program at the line computer (job control: red lamp).
Specify the new placement program.
Check the width of the conveyor belt.
Check the position of the magnetic supports and make sure that they cannot collide with components on
the bottom of the PCB.
Carry out the set-up check.
Check that the feeder modules are equipped with the correct components and that they are at the correct
locations.
Check the nozzle configuration.
If no nozzle changer is installed, you must change the nozzles manually.
PLEASE NOTE:
If you change the nozzle manually, ALWAYS ensure that the nozzle is seated correctly and that you are
using the correct nozzle type.
If you have not inserted a nozzle or have used the wrong nozzle type, the program will prompt you to move
the placement head to the service position and change the nozzle. This error message will also appear if
you have not inserted the nozzle correctly.
If you insert the wrong nozzle or use the wrong nozzle type again, the gantry will move to the service posi-
tion once more after the reference sequence. The program will continue to prompt for a nozzle change
until you have obtained the correct configuration. If you do not succeed then proceed as follows:
– Switch off the station and cancel the program being sent to the station at the line computer.
– Rectify the nozzle error and restart the station.
TIP
Have the nozzles ready in a separate nozzle box - identify each compartment with the nozzle type and
color. This will prevent any confusion.
Do not raise used plastic nozzles. Just dispose of them immediately.
Fig. 6.3.1 Nozzle box
701
yellow
704
orange
705
red
711
yellow