80S-2080F480F5 - 第43页
SIPLACE 80S-20/F4/F5 User M anual 1 Operational Safety 05/99 Issue from Software Version SR.405.xx 1.1 Information on safety 1 - 5 DANGER This mac hine is electricall y powere d. When el ectrical e quipment i s being u s…
1 Operational Safety SIPLACE 80S-20/F4/F5 User Manual
1.1 Information on safety 05/99 Issue from Software Version SR.405.xx
1 - 4
1.1.3 Use as prescribed
WARNING
The product must only be used for the applications specified in the catalogs and technical descriptions, and
then only in conjunction with non-Siemens devices and components that have been approved by Siemens.
For the product to operate correctly and reliably, it must have been transported, stored, erected and assembled
correctly and must be operated and maintained with care.
1.1.4 Important notes on operational safety
WARNING
In order to assure operational safety the following points must be observed without fail:
- NEVER open one of the two protective covers if you are not totally familiar with the sequence and function-
ing of the machine. Do not open the protective covers during operation unless you are told to do so in this
User Manual or in the station software dialog.
- Only trained and qualified personnel may set the key switch to set-up mode ("I").
- During operation, do not set the key switch to the "I" position (set-up mode) unless prompted to do so in
this manual or by the station software.Never bring your head or arms into the travel area of the gantry
when a station is switched on!
- No modifications of any type whatsoever may be made where it is not absolutely clear what effect they
would have on the functioning of the unit as a whole!
- The stations may only be adjusted, converted or maintained by personnel trained in this!
- Only use original spare parts and authorized accessories from Siemens AG. Using other parts will impair
safety and may cancel any liability of Siemens AG for the consequences.
- The operating safety of the SMD placement machines can only be guaranteed when the SMD placement
machines are used properly and for the purpose intended and when the provisions of the user’s manual
are complied with.
- The key for opening control and servo unit doors and the key for the key switch should be kept in a place
that is only accessible to qualified personnel.
- If it is necessary to work on the machine and you do not have enough trained personnel available in your
plant, always call in a service technician from Siemens AG. Siemens AG will not accept any claims for
damage or consequential damage that is the result of incorrect work.
- Machine operators must only carry out work for which they have been adequately trained and with which
they are totally familiar.
- You must also follow any special safety regulations applicable in your own country.
- Protective devices must NOT be modified. In particular, circuit-breakers must never be by-passed and pro-
tective devices must never be removed.
- If particular hazards are identified while the machine is in use, the machine operator must immediately
notify the manufacturer in writing so that the manufacturer can take appropriate action to minimise the
potential danger.
SIPLACE 80S-20/F4/F5 User Manual 1 Operational Safety
05/99 Issue from Software Version SR.405.xx 1.1 Information on safety
1 - 5
DANGER
This machine is electrically powered. When electrical equipment is being used, certain parts must of necessity
be live with dangerous voltages!
Always switch off the automatic placement system at the main switch and isolate it from the power supply be-
fore carrying out any work on live parts.
Failure to comply with all instructions may result in serious injury, death and/or considerable damage to
property!
WARNING
Despite all of the safety measures provided by the manufacturer severe injuries to person (e.g. by the gantry)
and/or considerable material damage can occur if the machine is improperly operated! Safe operation of the
machine presupposes that the machine is operated properly by qualified personnel with all warning notes being
observed! Certain work on the machine (e.g. setting-up and adjustment) demand training which goes beyond
the contents of this operating manual.
1 Operational Safety SIPLACE 80S-20/F4/F5 User Manual
1.1 Information on safety 05/99 Issue from Software Version SR.405.xx
1 - 6
1.1.5 Warning signs on the placement system
The diagram below shows the position of the warning signs on the basic machine.
Fig. 1.1.1 Warning signs on the basic machine - part 1
Item 1 in Fig. 1.1.1 showing the warning signs on the basic machine