Dek-265GSX-User-Manual - 第107页
19. The printer operates continuously. The menu bar displays the following options, these may be selected at any time during a print run: End Run Selecting this option stops the printer on completion of the current print…
8. Insert a 0.25mm feeler between the deflector and the screen. Tighten the
screws checking that the 0.25mm gap remains.
9. Repeat Steps 7 and 8 for the other deflector.
10. Lower the front printhead cover.
11.
Press the System button.
12.
Select Continue (F1).
Continue
13.
Afterthesqueegeehasmovedapproximately20mm,selectStopCycle(F2).
Stop
Cycle
14. Lift the front printhead cover. Check the deflectors are not touching the
screen.
15. Lower the front printhead cover.
16.
Press the System button.
17.
Select Continue (F1).
Continue
18. Repeat Steps 5 - 17 for the other squeegee.
1.90 User Manual Software Version 6
MACHINE PROGRAMMING
STAGE 10
19. The printer operates continuously. The menu bar displays the following
options, these may be selected at any time during a print run:
End Run Selecting this option stops the printer on completion of the current print cycle.
Stop Cycle Selecting this option stops the printer immediately, halting all actions.
Paste Load Selecting this option allows the operator to load paste to the screen either
manually or automatically.
Clean Screen Selecting this option allows the operator to clean the screen in addition to the
programmed cleaning intervals.
Adjust Selecting this option allows the operator to adjust any of the main process
parameters displayed on the pop-up menu without having to access the main
menu or stop the machine.
The machine continues to run using the existing values, when Exit (F8) is
selected the new values are used.
To save the new values, select Setup (F6), select Edit Data (F3), select Save
(F2), select Exit (F8).
Knead Paste Selecting this option runs the knead paste process in addition to the programmed
cleaning intervals.
Adjust Inspect Selecting this option allows the operator to edit 2D inspection parameters.
NOTE
Global Limits, Limit Sets and Sit parameters can be edited. Site Co-ordinates
can not be adjusted. Any changes made to inspection parameters are saved on
exit.
Software Version 6 User Manual 1.91
MACHINE PROGRAMMING
STAGE 10
MENU PARAMETERS
Each product has a set of parameters which are unique to that particular product
and which need to be setup to obtain acceptable printing results. These
parametersarelistedbelowwithadefinitionofeachasanaidtomachine setup.
NOTE
Machines running software version 2.06 and above have the ability to read
product files generated by a DEK 288 printing machine.
Parameter Definition
Product Name The file name for the particular product. The name can consist of up to eight
alphanumeric characters with no punctuation.
Product ID The product ID is a parameter that allows a descripton of the product. This
string may be up to 32 characters long, but only the first 20 characters are
displayed.
Product Barcode
(265GSX only)
The barcode number for the particular product. The barcode can be up to
twenty characters long. This parameter is only used if the machine is fitted
with a product barcode reader.
Screen Barcode (265GSX
only)
The barcode number that identifies the particular screen to be used with this
particular product. The barcode can be up to twenty characters long. If the
screen has a barcode printed on it in the correct place and the machine is
initialized to read the code, the screen is checked to ensure it is correct after it
has been fitted. If it is incorrect a message is displayed on the monitor. This
parameter is only used if the machine is fitted with a product barcode reader.
Board Length This parameter is used to set the default values for the board stop position in
the X direction, the paste dispensing area, and the AutoFlex reset columns.
The maximum value depends on the type of screen selected.
Min. Allowable 50mm (see Note 1.)
Max. Allowable
265 508mm (see Notes 1. and 2.)
255 460mm
249 430mm
Fuji 460mm
Sanyo 420mm
Heraeus 344mm
In increments of 0.1mm
NOTE
1. With remote board stop fitted
Min. Allowable 130mm
Max. Allowable 508mm (see Note 2.)
2. With the large board option the Max. Allowable is 620mm.
Although the maximum parameter is 620mm boards of
664mm can be loaded.
Board Width This parameter sets the rail width for this particular product. It is also used to
set a default value for the print stroke, the clean screen, the board stop
position in the Y direction, and the autoflex rows. The maximum value
depends on the screen type selected.
Min. Allowable 40mm
Max. Allowable
265 508mm
255 432mm
249 330mm
Fuji 460mm
Sanyo 284mm
Heraeus 344mm
In increments of 0.1mm
NOTE
With remote board stop fitted
Min. Allowable 119mm
Max. Allowable 508.5mm
1.92 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS