Dek-265GSX-User-Manual - 第117页

Parameter Definition Vortex Cassette Life (Vortex USC) This parameter sets the number of cleaning strokes that are applied before a cleaning cassette is replaced. Minimum 0 Maximum 200 Default 20 Increment 1 Vortex Clean…

100%1 / 388
Parameter Definition
Dry Clean Speed This parameter sets the speed of the screen clean dry wipe for optimization of
the blue or silver USC and the speed of the screen clean return stroke for the
Vortex USC.
Minimum 10 mm/sec
Maximum 120mm/sec
Default 30mm/sec
Increments 1mm/sec steps
Wet Clean Speed This parameter sets the speed of the screen clean wet wipe for optimization.
Minimum 10 mm/sec
Maximum 100mm/sec
Increments 1mm/sec steps
Vac Clean Speed This parameter sets the speed of the screen clean Vacuum for optimization.
Minimum 10 mm/sec
Maximum 100mm/sec
Increments 1mm/sec steps
Clean After Downtime This function provides the facility for the screen to be cleaned automatically
with a pre-programmed clean after a pre-programmed idle time. Clean After
Downtime only becomes active after the machine has performed at least one
print after it is powered up. When selected this parameter opens a window
that allows a clean after knead option sequence to be chosen. The sequence
includes six stages, each of which may be one of the following cleaning
operations:
WET, DRY, VAC, NONE
Clean After The Automatic screen clean after downtime process chosen in the above
menu parameter is carried out after a countdown of the number of minutes set
in this parameter.
Minimum 5 mins.
Maximum 120 mins.
Increment 1 min.
Clean After Knead This function is active if the machine is running in automatic mode. If this
option is enabled and a paste dispense has been performed (either MANUAL
or AUTOMATIC) a paste knead is performed as defined by the paste knead
parameters in the board file on the next board immediately following the
paste dispense. When selected this parameter opens a window that allows a
clean after knead option sequence to be chosen. The sequence includes six
stages, each of which may be one of the following cleaning operations:
WET, DRY, VAC, NONE
Front Start Offset
(Blue/Silver USC)
This parameter determines the distance from the front edge of the board that
the cleaning stroke must start.
Minimum 0mm
Maximum 60mm
Increments 1mm
Front Start Offset
(Vortex USC)
The distance, in from the front edge of the board, at which the cleaner is to
finish.
Minimum -60mm
Maximum 60mm
Default 30mm
Increment 1mm
Rear Start Offset
(Blue/Silver USC)
This parameter determines the distance from the rear edge of the board that
cleaning must complete.
Minimum 0mm
Maximum 60mm
Increments 1mm
Rear Start Offset
(Vortex USC)
The distance, in from the rear edge of the board, at which the cleaner is to
start.
Minimum -60mm
Maximum 60mm
Default 30mm
Increment 1mm
1.100 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Vortex Cassette Life
(Vortex USC)
This parameter sets the number of cleaning strokes that are applied before a
cleaning cassette is replaced.
Minimum 0
Maximum 200
Default 20
Increment 1
Vortex Clean Rate
(Vortex USC)
This parameter sets the frequency (in print cycles) at which screen cleaning
occurs.
Minimum 0
Maximum 200
Default 0
Increment 1
Vortex Solvent Rate
(Vortex USC)
This parameter sets the frequency (in cleaning cycles) at which solvent is
dispensed.
Minimum 1
Maximum 10
Default 1
Increment 1
Vortex Vacuum Start
(Vortex USC)
The distance, in from the front edge of the board, where vacuum is applied.
Minimum Vacuum Stop
Maximum Board Width
Default 0mm
Increment 1mm
Vortex Vacuum Stop
(Vortex USC)
The distance, in from the front edge of the board, where vacuum application
is stopped.
Minimum -100mm
Maximum Vacuum Stop
Default 0mm
Increment 1mm
Vortex Vacuum Rate
(Vortex USC)
This parameter sets the frequency (in cleaning cycles) at which vacuum is
applied.
Minimum 1
Maximum 10
Default 1
Increment 1
Vortex Vacuum Period
(Vortex USC)
This parameter sets the period for which vacuum is applied.
Minimum 1 sec
Maximum 10 secs
Default 5 secs
Increment 1 sec
Paste Dispense Rate This parameter sets the number of print cycles which occur between cycling
of the paste dispense system.
Minimum 0 (Dispenser switched off)
Maximum 100
Increment 1
Paste Dispense Speed This parameter sets the speed at which the paste dispenser moves across the
screen thereby determining the amount of paste deposited on the screen.
Minimum 10mm/sec
Maximum 100mm/sec
Increment 1mm/sec
Software Version 6 User Manual 1.101
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Paste Start This parameter determines start position of the paste dispense measured from
the centre line of the machine. The limits depend on the type of screen fitted.
Minimum
No adapter -255mm
255 -230mm
Sanyo -210mm
Heraeus -172mm
249 -215mm
Default -half the board length
Maximum
No adapter +255mm
255 +230mm
Sanyo +210mm
Heraeus +172mm
249 +215mm
Default +half the board length
Paste stop This parameter determines the stop position of the paste dispense measured
from the centre line of the machine. The maximum value depends on the
type of screen fitted.
Minimum
No adapter -255mm
255 -230mm
Sanyo -210mm
Heraeus -172mm
249 -215mm
Default -half the board length
Maximum
No adapter +255mm
255 +230mm
Sanyo +210mm
Heraeus +172mm
249 +215mm
Default +half the board length
Knead Boards This parameter sets the number of boards to be printed using the knead
sequence.
Minimum 1
Maximum 10
Increment 1
Knead Deposits This parameter sets the number of print strokes to be carried out on each of
the kneaded boards.
Minimum 2
Maximum 20
Increment 1
Paste Knead Period This parameter sets the time period between print cycles which, if exceeded,
initiates a paste knead sequence.
Minimum 0 (paste kneading switched off)
Maximum 30 minutes
Increment 1 minute
Knead After Dispense If this option is enabled and a paste dispense has been performed (either
Manual or Automatic) a paste knead is performed (as defined by the paste
knead parameters in the board file) on the next board immediately following
the paste dispense.
ENABLED; DISABLED
Paste While Clean This parameter enables the machine to carry out a paste dispense while
cleaning the screen. Available modes are:
DISABLED, MODE 1, MODE 2, BOTH MODES
Alternate Disp This parameter gives the option to dispense at either ENDS or CENTRE.
ENDS dispenses at the outer 25% of the squeegees. CENTRE dispenses
along an area of 25% either side of the centre line.
ENDS; CENTRE
1.102 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS