Dek-265GSX-User-Manual - 第118页

Parameter Definition Paste Start This parameter determines start position of the paste dispense measured from the centre line of the machine. The limits depend on the type of screen fitted. Minimum No adapter -255mm 255 …

100%1 / 388
Parameter Definition
Vortex Cassette Life
(Vortex USC)
This parameter sets the number of cleaning strokes that are applied before a
cleaning cassette is replaced.
Minimum 0
Maximum 200
Default 20
Increment 1
Vortex Clean Rate
(Vortex USC)
This parameter sets the frequency (in print cycles) at which screen cleaning
occurs.
Minimum 0
Maximum 200
Default 0
Increment 1
Vortex Solvent Rate
(Vortex USC)
This parameter sets the frequency (in cleaning cycles) at which solvent is
dispensed.
Minimum 1
Maximum 10
Default 1
Increment 1
Vortex Vacuum Start
(Vortex USC)
The distance, in from the front edge of the board, where vacuum is applied.
Minimum Vacuum Stop
Maximum Board Width
Default 0mm
Increment 1mm
Vortex Vacuum Stop
(Vortex USC)
The distance, in from the front edge of the board, where vacuum application
is stopped.
Minimum -100mm
Maximum Vacuum Stop
Default 0mm
Increment 1mm
Vortex Vacuum Rate
(Vortex USC)
This parameter sets the frequency (in cleaning cycles) at which vacuum is
applied.
Minimum 1
Maximum 10
Default 1
Increment 1
Vortex Vacuum Period
(Vortex USC)
This parameter sets the period for which vacuum is applied.
Minimum 1 sec
Maximum 10 secs
Default 5 secs
Increment 1 sec
Paste Dispense Rate This parameter sets the number of print cycles which occur between cycling
of the paste dispense system.
Minimum 0 (Dispenser switched off)
Maximum 100
Increment 1
Paste Dispense Speed This parameter sets the speed at which the paste dispenser moves across the
screen thereby determining the amount of paste deposited on the screen.
Minimum 10mm/sec
Maximum 100mm/sec
Increment 1mm/sec
Software Version 6 User Manual 1.101
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Paste Start This parameter determines start position of the paste dispense measured from
the centre line of the machine. The limits depend on the type of screen fitted.
Minimum
No adapter -255mm
255 -230mm
Sanyo -210mm
Heraeus -172mm
249 -215mm
Default -half the board length
Maximum
No adapter +255mm
255 +230mm
Sanyo +210mm
Heraeus +172mm
249 +215mm
Default +half the board length
Paste stop This parameter determines the stop position of the paste dispense measured
from the centre line of the machine. The maximum value depends on the
type of screen fitted.
Minimum
No adapter -255mm
255 -230mm
Sanyo -210mm
Heraeus -172mm
249 -215mm
Default -half the board length
Maximum
No adapter +255mm
255 +230mm
Sanyo +210mm
Heraeus +172mm
249 +215mm
Default +half the board length
Knead Boards This parameter sets the number of boards to be printed using the knead
sequence.
Minimum 1
Maximum 10
Increment 1
Knead Deposits This parameter sets the number of print strokes to be carried out on each of
the kneaded boards.
Minimum 2
Maximum 20
Increment 1
Paste Knead Period This parameter sets the time period between print cycles which, if exceeded,
initiates a paste knead sequence.
Minimum 0 (paste kneading switched off)
Maximum 30 minutes
Increment 1 minute
Knead After Dispense If this option is enabled and a paste dispense has been performed (either
Manual or Automatic) a paste knead is performed (as defined by the paste
knead parameters in the board file) on the next board immediately following
the paste dispense.
ENABLED; DISABLED
Paste While Clean This parameter enables the machine to carry out a paste dispense while
cleaning the screen. Available modes are:
DISABLED, MODE 1, MODE 2, BOTH MODES
Alternate Disp This parameter gives the option to dispense at either ENDS or CENTRE.
ENDS dispenses at the outer 25% of the squeegees. CENTRE dispenses
along an area of 25% either side of the centre line.
ENDS; CENTRE
1.102 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Alternate Disp Rate This parameter enables the user to select the ratio of alternate dispenses to
standard dispenses.
No alternate dispense
Every dispense
Every second dispense etc.
Paste With Board This parameter gives the option to dispense paste with a board loaded and
held at print height. This prevents paste dropping through the image on the
screen. Options are:
ENABLED; DISABLED
NOTE
With enabled selected the parameter Paste While Clean is removed.
Board Count This function provides the facility for the print cycle to be halted
automatically on a board count basis. If the board stop count is zero this
function is not active. When a print run is started, a count is made from the
STOP CYCLE AFTER value to zero decrementing by one for each board
printed. When the counter reaches zero, the print cycle is finished and
control returned to the main display page and the beacon is set to amber, thus
indicating that the machine requires operator attention. The operator has
access to all of the machines options. Once the operator has performed any
required operations, the run button can be pressed to continue the print cycle.
Minimum 0 Boards
Maximum 500 Boards
Increments 1 Board
Stop After Idle This parameter when enabled sets the time the product is held in contact with
the screen until both upline and downline systems are ready to transfer.
Minimum 0 mins.
Maximum 200 mins.
Increments 1 min.
Screen X Forward Nominal position of the X front screen actuator which ensures that
corresponding screen and board fiducials can be viewed from a single camera
position.
Minimum -20mm
Maximum +20mm
Increment 0.004mm
Screen X Rear Nominal position of the X rear screen actuator which ensures that
corresponding screen and board fiducials can be viewed from a single camera
position.
Minimum -20mm
Maximum +20mm
Increment 0.004mm
Screen Y Axis Nominal position of the Y screen actuator which ensures that corresponding
screen and board fiducials can be viewed from a single camera position.
Minimum -10mm
Maximum +10mm
Increment 0.004mm
Cleaner Paper
Advance
The distance, measured in millimetres, by which the cleaner paper is
advanced.
Minimum 0
Maximum 200mm
Increment 4mm
SPC Configuration This preference allows the user to set up the Machines SPC operation. On
selecting the SPC Configuration by pressing the Incr. or Decr. buttons, a
window opens and the menu bar changes.
See the SPC Configuration section later in this chapter for further details.
Paste Ridge
Removal
This parameter enables the cleaning option Paste Ridge Removal. This
option removes the ridge of the paste that can develop on the underside of the
screen at the end of the under screen cleaner cleaning stroke.
Disabled; Enabled.
Default Disabled.
Software Version 6 User Manual 1.103
MACHINE PROGRAMMING
MENU PARAMETERS