Dek-265GSX-User-Manual - 第144页

Remote Barcode Hardware This preference is only available if the TCP/IP version of Host Comms is used and Serial Host Comms is not selected from the Comms Protocol set preference, options are: Enabled; Disabled The optio…

Comms Enabled Comms Disabled Equipment Constant Change

Acknowledge Terminal Message Comms Knead Paste Request Comms Condition Paste Request

Control State Change To Local Control State change To Offline Control State Change To Remote

GEM Spooling Activated Gem Spooling Deactivated GEM Spool Transmission Failure

Operator Command Issued Remote Barcode Received Comms Adjust ProFlow Pressure

Options.enb file Attribute Error Volume Alarm Evaluation Dongle Detected

Valid Dongle Detected Dongle Error Dongle Changed

Print Speed Front Print Speed Rear Print Speed

Comms Adjust Print Speed Comms Adjust Front Print Speed Comms Adjust Rear Print Speed

Vortex Cassette Replaced Maintenance Monitoring Initialis The Monthly Service is Due

The Six Monthly Service is Due The Yearly Service is Due Equipment Recovery

Equipment Setup Equipment Ready Equipment Maintenance

Equipment Waiting Equipment Running Equipment Down

Tooling Hardware Sets which type of tooling is fitted, options are:

Autoflex; Vacuum; Magnetic; Vac For Flex

The default is Magnetic.

Autoflex Entry Sets whether the Fine Pitch Autoflex pin co-ordinates are referenced by the

distance of the pin, in X and Y, from the front left of the Autoflex table

(absolute), or from the column letters and row numbers (grid), options are:

Absolute; Grid

Fiducial Reference Sets whether the fiducial co-ordinates are specified relative to the front/left or

front/right corner of the board:

Left; Right

The default is Left.

Product Barcode

H/W

Sets whether or not the product barcode reader is fitted (265GSX only), options

are:

Fitted; Not Fitted

Screen Barcode

H/W

Sets whether or not the screen barcode reader is fitted (265GSX only), options

are:

Fitted; Not Fitted

Software Version 6 User Manual 2.9

SET PREFERENCES

PREFERENCES

Remote Barcode

Hardware

This preference is only available if the TCP/IP version of Host Comms is used

and Serial Host Comms is not selected from the Comms Protocol set preference,

options are:

Enabled; Disabled

The optional External Product Barcode Reader provides a generic bar code

interface for the capturing by GEM and SPC of a product bar code before the

product is passed to the printer. Use of the reader enables a host program to

decide on the action to be taken for this product and provides a method for SPC

to log product details for tracking.

The DEK printer acts as a dumb receiver of barcode data and provides no set up,

configuration or triggering information for the barcode reader.

Compatible Bar

Code Reader

The printer has been designed to operate with SICK Model CLV 212 Bar code

reader.

Options The two options available for the External Barcode parameter are Enabled and

Disabled.

If the bar code reader is set to Disabled, COM 1 is setup as per previous versions

of software and enabled to accept serial host comms.

If the bar code readeris set to Enabled, COM 1 isset to use the external bar code

reader and the option Serial Comms is removed from the Comms Protocol

parameter in the Set Preferences menu.

ProFlow Contact

Position

This parameter sets the height of theProFlow printhead so that it just touches the

stencil surface.

Min - 10mm

Max + 10mm

Increments 0.1mm

The default is 0mm.

ProFlow Down Stop

Position

This parameter pre-tensions the squeegee suspension springs to provide

ProFlow with a zero pressure datum.

Min - 10mm

Max 10mm

Increments 0.1mm

The default is 0mm.

2.10 User Manual Software Version 6

SET PREFERENCES

PREFERENCES

Change Mode

Option

Sets the screen change mode, options are:

Manual; Dual Shuttle

NOTE

The dual shuttle option is only relevant on a machine with a dual shuttle unit

fitted.

Screen Size Sets the screen size frame:

265; FUJI; 249; SANYO; SCREEN LIBRARY

With Screen Library enabled the printer is provided with detailed screen

dimensional information from a ‘read only’ library. This information is stored

within the machine configuration and product files.

Once selected in Set Preferences, detailed frame dimensions are provided to the

printer. In Edit Current Process Parameters, the parameter Image Data provides

comprehensive location and mesh details to the printer.

To enable screen library files carry out the following:

Highlight Screen Size in the Set Prefs page.

Using Incr. or Decr. select Screen Library.

Edit Data is now available on the menu bar.

Select Edit Data, the following window and menu bar is displayed:

Use Incr.orDecr. to select the required Screen Type. If no valid screen library

files are found, the default file DEK 265 Central Image is displayed.

Use Next or Previous to select and Incr. or Decr. to modify the screen frame

parameters as required.

Software Version 6 User Manual 2.11

SET PREFERENCES

PREFERENCES

SCREEN TYPE

SCREEN LENGTH

SCREEN WIDTH

FRAME FRONT

FRAME REAR

FRAME LEFT

FRAME RIGHT

DEK 265 CENTRAL IMAGE

XXX

Screen Frame Configuration