Dek-265GSX-User-Manual - 第379页

5. Fill the cavity until the paste starts to flow back up through the primary grid, extracting the nozzle slowly whilst continuing to fill. (This action fills the hole left by the nozzle.) 6. Move to the next available c…

Rechargeable

Transfer Head

It is necessary at intervals to replenish the rechargeable transfer head. If there is

no print medium in the transfer head at the end of a print stroke, the warning

window ‘Print Medium Low. Please Replenish.’ is displayed.

Initial Filling If an empty/new rechargeable transfer head is to be used prior to printing. The

transfer head unit is to be initially charged in accordance with the following:

1. Fit the clean/new transfer head to the maintenance stand, so that the unit is

upside down.

2. Remove wipers, end retainers (skis) and the secondary ProFlow grid to gain

access to the primary grid.

3. Ensure that the long nosed nozzle is fitted to the recharging gun (mastic or

pneumatic gun).

4. Starting at one end of the centre row of holes in the primary grid, insert the

gun nozzle through the grid into the area adjacent to the diaphragm.

9.64 User Manual Software Version 6

CONSUMABLE REPLENISHMENTS

PROFLOW

WARNING

PROTECTIVE CLOTHING. APPROVED PROTECTIVE CLOTHIN

SHOULD BE WORN BY SOLDER PASTEAND SOLVENT HANDLERS

AT ALL TIMES TO ELIMINATE FUME INHALATION, EYE

CONTACT,SKINCONTACTANDINGESTION.

WARNING

SOLDERPASTEANDSOLVENTS. WHENUSINGORHANDLINGAN

SOLDER PASTE OR SOLVENT FORMULATION THE

MANUFACTURERS' RECOMMENDED SAFETY PRECAUTIONS

MUSTBESTRICTLYADHEREDTO.

Long Recharging Nozzle

5. Fill the cavity until the paste starts to flow back up through the primary grid,

extracting the nozzle slowly whilst continuing to fill. (This action fills the

hole left by the nozzle.)

6. Move to the next available centre hole, in the primary grid, that has not been

filled with paste. Repeat Steps 4 and 5.

7. Continue the above procedures until all the space below the primary grid is

topped up with paste.

NOTE

Ensure that there is little or no air bubbles trapped within the paste fill.

8. Re-fitthesecondaryProFlowgrid, wipers and end retainers (skis) to the unit.

9. Starting at one end of the centre row of holes in the secondary ProFlow grid,

insert the gun nozzle through the grid into the conditioning chamber area.

10. Fill the cavity until the paste starts to flow back up through the ProFlow grid,

extracting the nozzle slowly whilst continuing to fill. (This action fills the

hole left by the nozzle.)

11. Move to the next available centre hole, in the secondary grid, that has not

been filled with paste. Repeat Steps 9 and 10.

Software Version 6 User Manual 9.65

CONSUMABLE REPLENISHMENTS

PROFLOW

Long Recharging Nozzle

12. Fill the remaining space between the secondary grid and the working edges

ofthe wiper blades ensuring that the paste is level, (procedurebelowrefers).

13. Fit paste cover to the unit.

14. Remove the transfer head from the maintenance stand and fit the unit to the

ProFlow on the machine. (Refer to Technical Reference Manual, ProFlow

Chapter, Setting Up Procedures for detailed information on unit

removal/fitting.)

The transfer head can be replenished prior to and during a print run.

Prior to a Print Run The transfer head can be replenished prior to selecting Run.

1. If the ProFlow unit is in the home position continue with Step 2. If the

ProFlow unit is in the contact position go to Step 20.

Select Setup (F6).

Setup

Select Setup ProFlow (F4).

Setup

ProFlow

Select Load Cassette (F4).

Load

Cassette

The message ‘Has the ProFlow unit’s base cover been removed?’ is

displayed.

5. If the ProFlow unit’s base cover is still fitted continue with Step 6. If the

ProFlow unit’s base cover has been removed go to Step 12.

9.66 User Manual Software Version 6

CONSUMABLE REPLENISHMENTS

PROFLOW