Dek-265GSX-User-Manual - 第76页

4. Select Change Tooling (F6). Change Tooling The Change Tooling Parameters window is displayed: The parameters are not active. 5. Select Adjust (F1). The parameters are now active. Adjust 6. Select Change Autoflex (F1).…

100%1 / 388
STAGE 6F
Tooling Setup - Fine Pitch AutoFlex
1. Place the PCB on a flat surface, component side up.
2. Position the acetate template, supplied with the tooling, over the PCB. Align
the centre of the PCB with the centreline of the template. Align the front
edge of the PCB with the line on the template.
3. Using the grid co-ordinates marked on the template, select which pins need
to be raised and which pins need to be lowered.
Software Version 6 User Manual 1.59
MACHINE PROGRAMMING
STAGE 6F
-236.5
-225.5
-214.5
-203.5
-192.5
-181.5
-170.5
-159.5
-148.5
-137.5
-126.5
-115.5
-104.5
-93.5
-82.5
-71.5
-60.5
-49.5
-38.5
38.5
49.5
60.5
71.5
82.5
93.5
104.5
115.5
126.5
137.5
148.5
159.5
170.5
181.5
192.5
203.5
214.5
225.5
236.5
487.5
476.5
465.5
454.5
443.5
432.5
421.5
410.5
399.5
388.5
377.5
366.5
355.5
344.5
333.5
322.5
311.5
300.5
289.5
278.5
267.5
256.5
245.5
234.5
223.5
212.5
201.5
190.5
179.5
168.5
157.5
146.5
135.5
124.5
113.5
102.5
91.5
80.5
69.5
58.5
47.5
36.5
25.5
14.5
-27.5
27.5
-16.5
16.5
-5.5
5.5
1
A
R
A
Q
A
P
A
O
A
N
A
M
A
L
A
K
A
J
A
I
A
H
A
G
A
F
A
E
A
D
A
C
A
B
A
A
ZYXWVUT
S
R
Q
P
O
NMLKJ I H
G
FED
millimetres
millimetres
millimetres
C
B
A
FRONT EDGE
OF BOARD
FRONT EDGE
OF BOARD
CENTRE LINE
OF BOARD
USAGE: 1. FLIP BOARD LEFT TO RIGHT
2. PLACE BOARD UNDER FILM
3. ALIGN CENTRE OF BOARD WITH CENTRE LINE ON FILM
4. ALIGN FRONT EDGE OF BOARDWITH LINE ON FILM
5. READ OFF GRID REFERENCES AND USE IN BOARD FILE
Note 2: THE FIGURES ACROSSTHE TOP OFTHE TEMPLATE
ARE REFERENCED TO THE CENTRE LINE OF THE BOARD
WHEREAS THE MMI MATRIX IS REFERENCED TO THE LEFT
OR RIGHT FRONT CORNER OF THE BOARD
Note 1: THE FIGURES DOWN THE RIGHT HAND SIDE OF THETEMPLATE
CORRESPOND TO THE FIGURES ON THE MMI MATRIX
AND REPRESENT THE DISTANCE FROM THE FRONT
EDGE OF THE BOARD
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
4.
Select Change Tooling (F6).
Change
Tooling
The Change Tooling Parameters window is displayed:
The parameters are not active.
5.
Select Adjust (F1). The parameters are now active.
Adjust
6.
Select Change Autoflex (F1). The message Use the ‘/’ key to enter
Numeric Block Control is displayed.
NOTE
This is only available if both Product File and Set Preferences have
AutoFlex selected.
Change
Autoflex
The Fine Pitch Autoflex Matrix window is displayed, showing the extent of the
rising table, the fine pitch Autoflex table and the current product:
1.60 User Manual Software Version 6
MACHINE PROGRAMMING
STAGE 6F
Change Tooling Parameters
BOARD WIDTH
BOARD STOP X
BOARD STOPY
216.0
125.0
142.6
mm
mm
mm
Rising Table
Fine Pitch
Autoflex Table
Current Product
Fine Pitch Autoflex Matrix
14.5
487.5
245.5
4.5
147.5
There are three ways of changing the pin configuration, as follows:
• Changing an area to either pins up or pins down
• Toggling state of individual pins
• Toggling state of pins in an area
Changing an Area to Either Pins Up or Pins Down
7. Press the forward slash key (/) on the keyboard.
The Fine Pitch Block Control window is displayed:
NOTE
If Grid is selected under Autoflex Entry in Set Prefs, the parameter values are
column letters and row numbers not in mm as shown.
8.
Use the Next and Previous keys (F4 - F5), to highlight each parameter in
turn.
Next Previous
9. Either:
a.
Use the Incr. and Decr. keys (F6 - F7), to set each of the values.
Incr. Decr.
Or:
b. (i). Press the forward slash key (/) on the keyboard. A window is displayed
for the selected parameter:
Software Version 6 User Manual 1.61
MACHINE PROGRAMMING
STAGE 6F
Fine Pitch Block Control
Block Origin X 0.0 mm
Block Origin Y 0.0 mm
Block Final X 152.0 mm
Block Final Y 101.0 mm