00197402-01 AI X-Feeder Upgrade Package - 第29页

X-Feeder Upgrade Install Removing the Left Side Cover AI X-Feeder Upgrade Package AI X-Feeder Upgrade Packa ge 29 3 3 X - F e e d e r U p g r a d e I n s t a ll X-Feeder Upgrade Install 3.1 3 . 1 R e m o v in g t h e L e…

Required parts

Content retrofit package

28 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

2.2

2.2 Content retrofit package

Content retrofit package

1. Stuffing gear interlocked

2. Stripping Device Foil Disposal

3. Sticker upgrade package

4. ISO4762 - M2 x 5-A2-70

5. ISO 7046-2-M2 x 4-A2-70-H

6. Flap / tape disposal complete

(No for X104)

7. Use cover strip rocker

8. Creasing rollers / PSA

9. Deflection sheet rocker (no for X16)

10. Stuffing gear interlocked complete rocker

11. Rocker (no for X16)

X-Feeder Upgrade Install

Removing the Left Side Cover

AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 29

3 X-Feeder Upgrade Install

X-Feeder Upgrade Install

3.1

3.1 Removing the Left Side Cover

Removing the Left Side Cover

3.2

3.2 Remove the cable connection to the distribution board

Remove the cable connection to the distribution board

Tools required:

▪ Phillips screwdriver

▪ TORX screwdriver size T8

► Carefully place the feeder module with the right-side

side down on a stable, level and clean surface.

► Loosen the screws as shown in the diagram.

Green arrows point to the screws for which you need a

TORX screwdriver with a torque of 0.6 Nm.

Blue arrows point to the screws for which you need a Phil

lips screwdriver with a torque of 0.9 Nm.

Start to loosen the screws at the position shown by the

green arrow.

► Lift the back of the side cover.

► Pull the side cover at a slight angle towards the back.

Make sure that you pull the lug straight out of the

drive unit.

► Place the side cover down on a clean, safe surface.

► (1) Pull the connector marked in the diagram up and

out of its connection.

To loosen the connector, move it carefully from side

to side.

► (2) Pull the connector marked in the diagram out of its

connection in the direction of the arrow. Pull on the

connector and NOT on the cable.

► (3) Carefully swing the lock on the flat ribbon cable

connection up to the left and release the flat ribbon

cable.

Make sure that the lock is not pushed too far back. It

could break off if you do this.

► Pull the connector shown in the diagram out of its

connection in the direction of the arrow. Pull on the

connector and NOT on the cable.

X-Feeder Upgrade Install

Remove the screws on the right side of the feeder

30 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

3.3

3.3 Remove the screws on the right side of the feeder

Remove the screws on the right side of the feeder

3.4

3.4 Dismantle of foil drive

Dismantle of foil drive

Tools required:

▪ Flat bladed (slotted) screwdriver

▪ hexagon socket 2

▪ TORX screwdriver size T8

▪ Split pin punch 1.4

► Carefully place the feeder module down on its left

side.

► (1) Loosen the screws of the foil container.

► (2) Remove the shaft and roller of the cover strip

rocker.

► (3) Press the rocker as far till it stop, into the spring,

to relieve the bearing shaft.

► Release the bearing shaft and remove the rocker.

Place the feeder carefully on a protected and cleaned

place.

Tools required:

▪ Phillips screwdriver

▪ TORX screwdriver size T8

► (1) Loosen the screws marked in the diagram.

► Turn the foil disposal drive over.

► (2) Loosen the screw marked in the diagram.

► (3) Loosen the screws marked in the diagram.