00197402-01 AI X-Feeder Upgrade Package - 第32页

X-Feeder Upgrade Install Replace parts of the rocker 32 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Packa ge 3.6 3 . 6 R e p la c e p a r t s o f t h e r o c k e r Replace parts of the rocker 3.7 3 . 7 F it t in g t …

X-Feeder Upgrade Install

Replacing the stuffing gear and parts of the cover strip rocker

AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 31

3.5

3.5 Replacing the stuffing gear and parts of the cover strip rocker

Replacing the stuffing gear and parts of the cover strip rocker

Tools required:

▪ Hexagon socket Gr. 2

▪ Phillips screwdriver

▪ Flat bladed (slotted) screwdriver

▪ Tweezers

► (1) Loosen the screws marked in the figure, at the top

and bottom of the stripping device. Depending on the

width of the feeder module, there will be up to a total

of 4 screws to be loosened at the top and bottom.

► (2) Loosen the screws on the cover sheet of disposal

drive.

► Lift the cover plate off the foil disposal drive.

► (1) Lift the gear stages with tweezers from the foil dis

posal drive.

Attention: The stage gear is greasy!

► (2) Remove the knurled stuffing gear and replace it

with the new "interlocked complete stuffing gear."

► Make sure that the corresponding washers are on the

toothed wheel axes (1).

► Place the cover plate on the slide disposal drive.

Make sure that the cover plate engages on the

toothed wheel axes (2) and the cover plate lies flat

level on the side cover.

► Fix the cover plate with the countersunk screws

marked in the diagram.

X-Feeder Upgrade Install

Replace parts of the rocker

32 AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package

3.6

3.6 Replace parts of the rocker

Replace parts of the rocker

3.7

3.7 Fitting the Flap Tape Disposal

Fitting the Flap Tape Disposal

► (1) Screw the new scraper plate, with the original

screws, slide the drive disposal, starting with the

overhead screws.

► Install the new folding roller (2) with the original shaft

and screw.

► Insert the "use foil wing" (3) and mount it with the orig

inal wave.

Caution! The originally present role is not needed and

is omitted.

Tools required:

▪ Phillips screwdriver

▪ Flat bladed (slotted) screwdriver

► (1) Remove the marked in the figure bearing shaft

from the old rocker.

► Insert the new stuffing gear (3) as shown in the new

rocker (4) and secure it with the previously removed

bearing shaft (2). Make sure that the stuffing gear can

move freely in the rocker.

► Insert the new wiper sheet (5) and secure it with the

screws, starting with the overhead screws.

► Open the flap.

► Replace the existing door carefully from the feeder.

► Place the new cover slowly in a foil container. The

spring (1) it is overridden. It is not necessary since the

function is now performed by the magnet (2).

X-Feeder Upgrade Install

Cover foil disposal install

AI X-Feeder Upgrade Package AI X-Feeder Upgrade Package 33

3.8

3.8 Cover foil disposal install

Cover foil disposal install

Tools required:

▪ Phillips screwdriver

▪ TORX screwdriver size T8

► (1) Press the foil disposal drive in the direction of the

arrow and into the foil container.

► Attach the film drive with the marked cylinder head

bolts. Be sure to insert the shims.

► (2) Fix the foil disposal drive into place with the cylin

der head screw marked in the diagram.

► (3) Turn the foil disposal to drive again and attach the

spacer to the marked in the figure Torx screws. Note

the correct position of the rubber seals (4).

► (1) Carefully place the feeder module down on its left

side. Position the foil container so that it is aligned

against the side cover.

► (2) Loosen the screws marked in the diagram.

► (1) Insert the flat ribbon cable into the connection, as

far as the stop. Make sure that the blue surface at the

end of the cable is at the top and that the flat ribbon

cable lies straight in the connection. Swing the lock

down onto the flat ribbon cable.

► (2) and (3) Carefully insert the connector in the direc

tion of the arrow, as far as the stop, into the connec

tion shown.

► (4) Insert the other connector into the connection

marked in the diagram.