CP-6-series Mechanical Reference - 第135页

Part 3 Chapter 3 Replacing Consumable Parts Edition 1.6 3-3-4 CP-6-series Mechanical Reference Part Numbers for the Nozzles and Reflective Disks φ 0.4 φ 0.7 φ 1.0 φ 1.3 φ 1.8 φ 2.5 φ 3.75 φ 2.5 φ 3.75 φ 5.0 φ 5.0 φ 7.0 φ…

Part 3 Chapter 3 Replacing Consumable Parts

Edition 1.6 3-3-3 CP-6-series Mechanical Reference

3.2 Nozzle Reflective Disk Replacement

Point

Replace the nozzle fluorescent seal if the seal becomes dirty and causes vision processing

errors.

Procedure

1. Always wash your hands before handling the seals.

2. Choose the correct disk, referring to table below if necessary.

3. Check that the fluorescent disk is free of deformity and is clean.

4. Peel the fluorescent disk from its paper backing and remove the small circular

cutout at the center of the seal by pushing it out from the side of the seal covered

with fluorescent paint. If the cutout is pushed out from the side covered with

adhesive, some of the fluorescent paint may be torn away when the circular cutout

comes loose from the rest of the disk.

5. Match the center of the disk with the center of the nozzle. Using jig (for reflective

plate), push the disk into the nozzle as shown in figure below. Check that no

space exists between the seal and the nozzle.

6. Use a utility knife to cut away any excess fluorescent seal.

7. Clean the fluorescent seal with a soft brush.

Note: Always use the jig because the fluorescent seal must be flat and centered on the disk.

Vision processing errors may occur if the inner edge of the seal contacts the pipe, if the seal

is torn, or if the seal hole does not line up with the pipe.

CP6MR009

Fluorescent seal

Nozzle

Expanded view

Correct

Incorrect (Seal contacts pipe)

Reflective disk

Jig

Reflective

disk size

Jig No.

ø12 ~ 20

❒22

❒22, ❒29

(Block type

for CP-65)

WPJ077✽

AWPJ910✽

YPJ070✽

CP6M3056

Part 3 Chapter 3 Replacing Consumable Parts

Edition 1.6 3-3-4 CP-6-series Mechanical Reference

Part Numbers for the Nozzles and Reflective Disks

φ0.4

φ0.7

φ1.0

φ1.3

φ1.8

φ2.5

φ3.75

φ2.5

φ3.75

φ5.0

φ7.0

φ10.0

AWPH970✽

AWPH951✽

AWPH952✽

AWPH953✽

AWPH955✽

AWPH956✽

AWPH957✽

AWPH958✽

AWPH960✽

AWPH961✽

AWPH966✽

AWPH968✽

AYPH951✽ *

AYPH953✽ *

φ12

φ16

φ20

❒20

❒22

❒29

WPH833✽

WPH829✽

WPH830✽

WPH831✽

WPH832✽

WPH820✽

WPH821✽

WPH808✽

WPH812✽

WPH810✽

WPH823✽

WPH818✽

YPH806✽

YPH857✽

φ5.0 AWPH967✽❒22 WPH822✽

φ7.0

AWPH969✽

AYPH952✽ *

❒22

❒29

WPH817✽

YPH858✽

CP6M3057Ea

Nozzle

size

Nozzle Assy No.

Reflective

disk size

Reflective

disk No.

For backlightFor frontlight

* Applies to the 5000-series nozzles.

Part 3 Chapter 3 Replacing Consumable Parts

Edition 1.6 3-3-5 CP-6-series Mechanical Reference

3.3 Vision Processing UV Lamp Replacement

Point

Oil from the skin may weaken the glass over time, reducing its lifespan.

Procedure

Warning

Turn off the main power before carrying out this work.

Remove the UV lamp by turning it and pulling it out.

Note : Avoid direct contact with the glass.

UV lamp

CP6M3058