CP-6-series Mechanical Reference - 第316页

Leveling (Left-Right) Left-right tilt is controlled by the main vibration reduction unit. Although the machine’s left-right height is normally adjusted using adhesive pads, special adjusting plates are required when the …

1.3 Installation Procedure

The installation positions for the vibration reducing units are shown below.

1. Place adhesive pads at the top and bottom faces of each unit.

2. Install each unit at its prescribed position.

Note: Never inflate the pneumatic spring prior to installation under the machine. Inflating

the unit prior to installation can cause it to burst.

Adhesive Pads

The adhesive pads are used to prevent positional shifts between the vibration reduction

units, the floor and the machine. Although standard adhesive pads are 4 mm thick, pads

with a 2 mm thickness are also available for height adjustment purposes. When

necessary, use a combination of both styles of pads.

Adhesive Pad List

Location Size (units: m/m) Qty Remarks

Main vibration reduction unit

(bottom)

200 x 450 x t4 4

(200x 450 x t2) 4 Sizes shown in parentheses are

Main vibration reduction unit (top) 130x 450 x t4 4 height adjusting pads

(130 x 450 x t2) 4

Spring unit (W2Q-434S) GERB x t4 3

(top & bottom) (GERB x t2) 3

Pneumatic spring (top & bottom) 380x 380 x t4 2

(380 x 380 x t2) 1

417.5750745

2930

3180 355215

125

(125) (125)

125

3750

770790277.5

1055

CP6M11003

Machine top

Part 10 Chapter 1 Vibration Reduction Unit

Edition 1.0 10-1-3 CP-6-series Mechanical Reference

Leveling (Left-Right)

Left-right tilt is controlled by the main vibration reduction unit.

Although the machine’s left-right height is normally adjusted using adhesive pads,

special adjusting plates are required when the adjustment amount exceeds 5 mm.

These adjusting plates are available in 5, 10, 15 and 20 mm thicknesses.

Leveling (Front-Back)

Front-back tilt is automatically adjusted by the pneumatic spring. A leveling valve is

activated to maintain the setting height when the back of the machine drops below the

preset height.

Adjusting Plate List

Dwg. No. Part Name Qty Thickness

9851DWAB1000 Plate 2 5 mmthick

9851DWAB1010 Plate 2 10mmthick

9851DWAB1020 Plate 2 15mmthick

9851DWAB1030 Plate 2 20mmthick

CP-642

Adhesive pad

Vibration proofing unit

Adjusting plate

CP6M11004

Part 10 Chapter 1 Vibration Reduction Unit

Edition 1.0 10-1-4 CP-6-series Mechanical Reference

1.4 Air Valve Modification and Adjustment

Modification

Add the necessary components as shown in the illustration below.

List of Added Parts

Adjustment

Main Vibration Reduction Unit

When a large number of tape feeders are installed on the device table, the regulator [3]

should be set to its full-open position. If only a few tape feeders are installed on the

device table and the load is light, adjust the regulator as appropriate for this load.

Normally, a setting of 3 kgf/cm2 is appropriate, although the adjustment range is 1~5

kgf/cm2. A higher pressure setting causes more vibration to be transmitted to the floor,

resulting in less vibration at the machine. A lower pressure setting causes less vibration

to be transmitted to the floor, resulting in more vibration at the machine.

No Dwg. No. Part Name Qty Model

1 9851DWAB Union 1 TS6-02

2 9851DWAB Union 1 TS4-02

3 9851DWAB Regulator 1 R150-02

4 H1214A Straight pipe 3 1/4x25

5 T4038A T-union 2 1/4

6 T2064A Hose (ø8) 1 m TU0805B-20

CP6M11005

After Modification

To Main vibration reduction unit

To Pneumatic spring

Part 10 Chapter 1 Vibration Reduction Unit

Edition 1.0 10-1-5 CP-6-series Mechanical Reference