CP-6-series Mechanical Reference - 第7页

T erminology Notice “ Production Program ” In this manual the term “ production program ” is used to refer to the operating instructions used by the machine in the production of a board. In FujiCam, this data is referred…

100%1 / 331
Body
The information needed to understand the workings of the machine and how to perform
operation is explained using text and illustrations.
Page number
A three digit hyphenated number appears in the footer on each page. The first digit of
each page number indicates the part number, the second digit indicates the chapter
number within the part, and the final digit is the sequential page number within that
chapter. Page 1-2-1, for example, indicates that this is the first page in the second chapter
of part 1.
Manual name
The name of the manual that appears on the cover is also shown in the footer on each
page.
Edition number
The edition number is updated each time the manual is revised, with the number
reflecting the scale of changes that were made.
Minor revision: Minor changes are reflected in the part of the edition number after
the decimal point, for example, a change from edition 1.0 to 1.1. This
change is made on the revised pages only, and these pages can be
downloaded as required from Fuji's website.
Major revision: If major changes are made, the edition number is increased by one,
for example, a change from edition 1.0 to 2.0.
Note: The reference numbers at the bottom right of the illustrations are for administrative
purposes only, and are in no way connected to the content of the manual.
Notation Conventions Used in this Manual
The notation conventions employed in this manual are described below.
[Production] command The names of the command buttons are enclosed in
brackets, and use the verb “press”.
START button Buttons on the machine are written exactly as they
appear, and use the verb “press”.
“Production” command section The names of commands that have been grouped
together are enclosed in quotation marks.
[TAB] key Keys on the keyboard appear in brackets.
About This Manual
Edition 1.6 iii CP-6-series Mechanical Reference
Terminology Notice
“Production Program” In this manual the term “production program” is
used to refer to the operating instructions used by the
machine in the production of a board.
In FujiCam, this data is referred to as the “recipe”.
Despite the differences in name, the terms carry the
same meaning, and references to “production
program” may therefore be thought of as “recipe” by
FujiCam users.
“Board”, “Block” In this manual the term “board” is used to refer to
the printed circuit on which parts are placed, and the
term “block” is used for multiple identical circuits
that may exist within a board and which are split into
individual units when production is complete.
In FujiCam, these terms are referred to as “panel”
and “board” respectively.
Despite the differences in name, the terms used in
this manual carry the same meaning as the
corresponding FujiCam terminology and can
therefore be freely interchanged by FujiCam users.
About This Manual
Edition 1.6 iv CP-6-series Mechanical Reference
Contents –
List of Current Pages
Safety Guidelines......................................................(Edition 1.5)
1. About Symbols.......................................................................................1
2. Safety Rules for All Machine Types.......................................................2
3. Safety Rules for Individual Machine Types............................................8
CP-6-series Machines..................................................................................................8
4. Safety Labels.......................................................................................10
5. The EMERGENCY STOP Button........................................................15
6. Before Operation .................................................................................17
7. Do not Leave Tools in or on the Machine ............................................17
Part 1 Introduction
1. Machine Components ..........................................(Edition 1.1) ......1-1-1
1.1 Front View of the Machine..............................................................................1-1-1
1.2 Rear View of the Machine...............................................................................1-1-2
1.3 Parts Related to the Drive Unit.......................................................................1-1-4
2. Functions of Each Component .............................(Edition 1.1) ......1-2-1
2.1 Parts Mounting System ..................................................................................1-2-2
2.1.1 Cam Box.......................................................................................1-2-2
2.1.2 The Index Units ............................................................................1-2-4
2.1.3 XY-Table (Main Conveyor)...........................................................1-2-5
2.1.4 The Placing Head.........................................................................1-2-9
2.1.5 The Twenty Stations...................................................................1-2-10
2.2 Parts Supply System ....................................................................................1-2-12
2.2.1 Feeders ......................................................................................1-2-12
2.2.2 Device Tables (except for CP-652CE) .......................................1-2-12
2.2.3 Tape Cutter ................................................................................1-2-13
2.2.4 Pallet Feeder (Only for the CP-652C) ........................................1-2-13
2.3 Vision System...............................................................................................1-2-14
2.3.1 Parts Cameras ...........................................................................1-2-14
2.3.2 Fiducial Mark Reading................................................................1-2-14
2.4 Board Conveyance.......................................................................................1-2-15
2.5 Electrical Control System..............................................................................1-2-17
2.5.1 Operation Panels........................................................................1-2-17
2.5.2 Servo Boxes...............................................................................1-2-18
2.6 The VME Rack..............................................................................................1-2-19
2.7 Pneumatic Control System...........................................................................1-2-21
3. Sensor Positions...................................................(Edition 1.0) ......1-3-1
3.1 Stations...........................................................................................................1-3-1
3.2 Axes................................................................................................................1-3-7
3.3 Loading System............................................................................................1-3-11
Contents – List of Current Pages
Edition 1.6 v CP-6-series Mechanical Reference