IPC-SM-782A-表面贴装焊盘图形设计标准.pdf.pdf - 第117页

1.0 SCOPE This subsection provides the component and land pattern dimensions for small outline integrated circuits (SOIC compo- nents) with gullwing leads. Basic construction of the SOIC device is also covered. At the en…

100%1 / 228
This Page Intentionally Left Blank
IPC-SM-782
Subject
Components with Gullwings on Two Sides
Date
8/93
Section
9.0
Revision
Page2of2
1.0 SCOPE
This subsection provides the component and land pattern
dimensions for small outline integrated circuits (SOIC compo-
nents) with gullwing leads. Basic construction of the SOIC
device is also covered. At the end of this subsection is a list-
ing of the tolerances and target solder joint dimensions used
to arrive at the land pattern dimensions.
2.0 APPLICABLE DOCUMENTS
See Section 9.0 for documents applicable to the subsections.
3.0 COMPONENT DESCRIPTIONS
These components are all on 1.27 mm pitch, and are available
in narrow body (3.90 mm), wide body (7.50 mm) and extra
wide body (8.90 mm) sizes, ranging from 8 to 36 pins.
3.1 Basic Construction See Figure 1. Basic construction
consists of a plastic body and metallic leads.
3.1.1 Termination Materials Leads should be solder-
coated with a tin/lead alloy. The solder should contain
between 58 to 68% tin. Solder may be applied to the termi-
nation by hot dipping or by plating from solution. Plated sol-
der terminations should be subjected to a post-plating reflow
operation to fuse the solder. The tin/lead finish should be at
least 0.00075 mm [0.0003 in] thick.
Solder finish applied over precious-metal leads shall have a
diffusion-barrier layer between the lead metallization and the
solder finish. The barrier layer should be nickel or an equiva-
lent diffusion barrier, and should be at least 0.00125 mm
[0.00005 in] thick.
3.1.2 Marking All parts shall be marked with a part number
and ‘‘Pin 1’’ location. ‘‘Pin 1’’ location may be molded into the
plastic body.
3.1.3 Carrier Package Format Bulk rods, 24 mm tape/
8–12 mm pitch is preferred for best handling. Tube carriers
are also used.
3.1.4 Resistance to Soldering Parts should be capable of
withstanding ten cycles through a standard reflow system
operating at 215°C. Each cycle shall consist of 60 seconds
exposure at 215°C. Parts must also be capable of withstand-
ing a minimum of 10 seconds immersion in molten solder at
260°C.
IPC-782-9-1-1
Figure 1 SOIC construction
IPC-SM-782
Surface Mount Design
and Land Pattern Standard
Date
5/96
Section
9.1
Revision
A
Subject
SOIC
Page1of4
4.0 COMPONENT DIMENSIONS
Figure 2 provides the component dimensions for SOIC components.
Component
Identifier
JEDEC
Number
L (mm) S (mm) W (mm) T (mm) A (mm) B (mm) H (mm)
P
(mm)
min max min max min max min max min max min max min max basic
S08 MS-012
AA
5.80 6.20 3.26 4.55 0.33 0.51 0.40 1.27 3.80 4.00 4.80 5.00 1.35 1.75 1.27
S08W — 10.00 10.65 7.46 8.85 0.33 0.51 0.40 1.27 7.40 7.60 5.05 5.45 2.35 2.65 1.27
S014 MS-012
AB
5.80 6.20 3.26 4.55 0.33 0.51 0.40 1.27 3.80 4.00 8.55 8.75 1.35 1.75 1.27
S014 W — 10.00 10.65 7.46 8.85 0.33 0.51 0.40 1.27 7.40 7.60 8.80 9.20 2.35 2.65
S016 MS-012
AC
5.80 6.20 3.26 4.55 0.33 0.51 0.40 1.27 3.80 4.00 9.80 10.00 1.35 1.75 1.27
S016W MS-013
AA
10.00 10.65 7.46 8.85 0.33 0.51 0.40 1.27 7.40 7.60 10.10 10.50 2.35 2.65 1.27
S020W MS-013
AC
10.00 10.65 7.46 8.85 0.33 0.51 0.40 1.27 7.40 7.60 12.60 13.00 2.35 2.65 1.27
S024W MO-119
AA
10.29 10.64 8.21 9.01 0.36 0.51 0.53 1.04 7.40 7.60 15.54 15.85 2.34 2.64 1.27
S024X MO-120
AA
11.81 12.17 9.73 10.54 0.36 0.51 0.53 1.04 8.76 9.02 15.54 15.85 2.34 2.64 1.27
S028W MO-119
AB
10.29 10.64 8.21 9.01 0.36 0.51 0.53 1.04 7.40 7.60 18.08 18.39 2.34 2.64 1.27
S028X MO-120
AB
11.81 12.17 9.73 10.54 0.36 0.51 0.53 1.04 8.76 9.02 18.08 18.39 2.34 2.64 1.27
S032W MO-119
AC
10.29 10.64 8.21 9.01 0.36 0.51 0.53 1.04 7.40 7.60 20.62 20.93 2.34 2.64 1.27
S032X MO-120
AC
11.81 12.17 9.73 10.54 0.36 0.51 0.53 1.04 8.76 9.02 20.62 20.93 2.34 2.64 1.27
S036W MO-119
AD
10.29 10.64 8.21 9.01 0.36 0.51 0.53 1.04 7.40 7.60 23.16 23.47 2.34 2.64 1.27
S036X MO-120
AD
11.81 12.17 9.73 10.54 0.36 0.51 0.53 1.04 8.76 9.02 23.16 23.47 2.34 2.64 1.27
Figure 2 SOIC component dimensions
P
H
SL
W
B
A
T
IPC-782-9-1-2
IPC-SM-782A
Subject
SOIC
Date
5/96
Section
9.1
Revision
A
Page2of4