00197623-03_VD_708.1_SP2_DE_EN - 第33页

Station Software 7 08.1 SP2 / Version Description Ausgabe 10/2015 E dition 33 708.1 SP1 Statio n Software V ersion The 708.1 SP1 stat ion software v ersion contains all e rror correctio ns of the previous 7 01.xx – 708.1…

Station Software 708.1 SP2 / Version Description Ausgabe 10/2015 Edition

9 Corrected Errors

708.1 SP2 Station Software

The 708.1 SP2 station software version contains all error corrections of the previous 701.xx –

708.1 SP1 versions. Additionally, the following errors have been corrected in this version:

Error no. Error description

D1-114620601 The CAN card was not recognized during the first machine configuration.

D1-114934101 The production could not be started when a connected MTC was switched off.

D1-116350301 Sporadically LED components were placed separately and this reduced the

performance of the machine.

D1-116638601 Changes within the parameter settings for the Glue Feeder were not

transferred to the feeder.

D1-116695601 Sporadically, a nozzle could neither be put back into the magazine nor

rejected.

D1-114908602 A dirty or defective pressure regulation valve was not detected.

D17753-22701 Conveyor parameter Current at lifting table was not calculated correctly.

708.1 SP1 HF2

D1-114615401 During production the station software interface was suddenly no longer

responding. After restart it was ok.

D1-116251101 Feeder error messages were no longer included in the "EventLog" file.

708.1 SP1 HF1

D1-114500709 The C&P20 P component sensor calibration was not successful.

D1-114651365 eSW: The board could not be transported with the Advanced PCB Interface.

D1-114925901 The occupancy check for the MTC did not report any error message in case of

a faulty occupancy.

D1-115713001

D1-115727701

D1-115788501

The CPP component censor calibration was not successful; the height

reference run of the 2

segment broke.

D1-115729601

D1-115739301

The temperature compensation could not be started although the temperature

was shown and the sensor running.

D1-115758001 eSW: The PCB barcode reader could not be configured.

Table 8-1: Corrected errors 708.1 SP2 station software version

Station Software 708.1 SP2 / Version Description Ausgabe 10/2015 Edition

708.1 SP1 Station Software Version

The 708.1 SP1 station software version contains all error corrections of the previous 701.xx –

708.1 versions. Additionally, the following errors have been corrected in this version:

Error no. Error description

D1-110371401 A nozzle got lost from the C&P20 P placement head during production but no

error message was displayed.

D1-112147342 The tape pocket measurement was too sensitive to lead deviations.

D1-112994843 Sporadically, the unknown HW error 0xF1 (DP axis) error message

was displayed.

D1-113336101 Some Reference Designators for some panels were missing in the traceability

system.

D1-114567701 Acknowledge of the buzzer was displayed even if the hardware was not

available on the machine.

D1-114583749 CA placement machine: the inspection of the chuck fiducials started although

it was deactivated.

D1-114679621 The software hung up when an error occurred during inkspot recognition.

D1-114940801

D17845-4407

There was no response from the MTC after a pickup error.

D1-115259384 After a product changeover, an unknown placement state (40020) was

reported endlessly for one component.

D1-115338650 Pitch too small error message was not reset after the manual correction

of the pitch.

D1-115304849 eSW: when production was continued after pressing the "stop" button and

opening the hood, the machine always executed a reference run.

708.1 HF04

D1-113666801 eSW: the transportation of the board into lane 1 or 2 via button on the GUI

failed if the cable of the advanced PCB interface was disconnected and

reconnected.

D1-114932601 eSW: there was a problem unloading a board if the length was between 930

and 985 mm.

D1-114932653 eSW: the conveyor lane width could not be adjusted because it had been set

too wide.

D1-114963801

D1-114935001

A collision of 2 gantries was reported.

D1-114999701 eSW: vacuum system: 30503 Supply pressure for pressure

control valve is missing

D1-115121901 Temperature compensation was not working correctly with C&P20 P

placement heads.

D1-115135201 eSW: the 3D-coplan module could not be measured. Windows hung up at the

first measurement.

D1-115160309 With HF3 some placement positions were out of the travel range.

Station Software 708.1 SP2 / Version Description Ausgabe 10/2015 Edition

708.1 HF03

D1-110371401 A nozzle from CP20P was lost during production.

D1-114077541 During production the lamp was blinking green. It should be green without

blinking.

D1-114530901 eSW: the communication between station and power supply was interrupted.

No answer from the main distributor for the subsystem.

D1-114557044 The software hung up when the trays were activated in the MTC.

D1-114641601 SX2 with DLM head at production area 2 and outer table: the nozzle changer

could not be configured with this machine configuration.

D1-114690122 When the component fiducial was taught the component shape wass not

visible.

D1-114734343 eSW: there was a transportation problem with boards between 245 and 240

mm length.

D1-114742101 The head could not reject component and not recover from error.

D1-114742141 There was an unhandled exception 30016.

D1-114785791

D1-114773701

D1-114817203

eSW: during production the machine stopped without an error message.

D1-114861301 The saving of the mapping data was improved.

D1-114872601 The tape cutter for gantry 2 wass not working and there was no error

message.

D1-114892301 eSW: machine zero point calibration was not possible.

D17931-3006 Communication problem with IPTE feeder after station software upgrade from

707 to 708.1.

708.1 HF02

D1-111491649 If the machine transferred a board to the next machine an error popped up for

1-2 seconds.

D1-112649181 Component sensor data on CPP could not be saved.

D1-112842103

D1-113896701

The nozzle scan failed if a component stuck on the nozzle.

D1-113386001

D1-113581429

D1-113718801

D1-114617201

D1-114627749

If you opened the cover there was no light in the machine. Update for

machines without cover lock.

D1-113809401 eSW: MGCU was not identified correctly.

D1-113930001 eSW: the application 1 for the Y axis was missing.

D1-113959701 After teaching and saving the placement position the component position had

still an offset.

D1-113970149 Unexpected software malfunction - restart necessary.