00196614-03_AI_Vakuumpumpe_SXDX12_de_en - 第110页
Fitting the Vacuum Pump Installing the Vacuum Pump 3.4.2 Connecting the Vacuum Hoses to the Distributor Block 110 Vacuum Pump Vakuumpumpe 3.4.2 3 . 4 . 2 C o n n e c t in g t h e V a c u u m H o s e s t o t h e D is t r …
Fitting the Vacuum Pump
3.4.1 Inserting the Pump into the Machine Installing the Vacuum Pump
Vacuum Pump Vakuumpumpe 109
3.4
3.4 Installing the Vacuum Pump
Installing the Vacuum Pump
The pump is installed at location 1.
See also
3.3.1 Installation Position - Accessibility and Preparations [ ➙ 90]
3.3.2 Prefitting the Vacuum Pump [ ➙ 92]
3.4.1 Inserting the Pump into the Machine [ ➙ 109]
3.4.3 Fitting the Air Outlet Conduit [03079527-xx] Under the Machine [ ➙ 110]
3.4.4 Connecting the Exhaust Tube ID100 [03087599-xx] [ ➙ 111]
3.4.2 Connecting the Vacuum Hoses to the Distributor Block [ ➙ 110]
3.4.1
3.4.1 Inserting the Pump into the Machine
Inserting the Pump into the Machine
► Place the pump on a pallet truck with a suitable base
and secure this with a safety belt to prevent it falling
off.
► Move the pump in front of the machine installation lo-
cation.
CAUTION!
When sliding the fork of a fork-lift truck or similar equip-
ment underneath the machine, lower the fork sufficiently
to ensure that any parts under the base (such as the vac-
uum pump fixture plate) are not damaged.
NOTICE!
You might need to enlist the help of a second person to
prevent this.
► Place the pump on the assembly plate in the installa-
tion location and push in back as far as the stopper.
► Run the power cable to the other side in location area
2, where it can be plugged into the connection unit.
► Fix the vacuum hoses to the eyelet on the top of the
pump, with a cable tie. Make sure that the cables are
not pinched.
Fitting the Vacuum Pump
Installing the Vacuum Pump 3.4.2 Connecting the Vacuum Hoses to the Distributor Block
110 Vacuum Pump Vakuumpumpe
3.4.2
3.4.2 Connecting the Vacuum Hoses to the Distributor Block
Connecting the Vacuum Hoses to the Distributor Block
3.4.3
3.4.3 Fitting the Air Outlet Conduit [03079527-xx] Under the Machine
Fitting the Air Outlet Conduit [03079527-xx] Under the Machine
► Connect the vacuum hoses to the distributor block:
⇨ Hose 1 m vacuum pump SX12 [03090005-xx]
⇨ Hose 2 m vacuum pump SX12 [03090006-xx]
► For a complete head assembly, use the connections
in the row (1) or all angle connection in the row (2).
► If you are only connecting one head, close the con-
nections in the free row with dummy plugs.
Air outlet conduit before installation
The air outlet conduit must be placed under the machine
if the exhaust air is to be guided outside properly.
1. Slot
2. Screw and nib engage
3. Mounting plate
4. Stop position of pump
► The air outlet conduit is pushed under the pump dur-
ing installation, so that the screw fixed with adhesive
to the wedge and the nib on the base plate of the
pump (2) engage with one another. The wedge is
screwed to the mounting plate through the slots on
the left and right (1). (Screws: ISO4762-M8x40-A2-
70 [03042589-xx])
Fitting the Vacuum Pump
3.4.4 Connecting the Exhaust Tube ID100 [03087599-xx] Installing the Vacuum Pump
Vacuum Pump Vakuumpumpe 111
3.4.4
3.4.4 Connecting the Exhaust Tube ID100 [03087599-xx]
Connecting the Exhaust Tube ID100 [03087599-xx]
► Lift the vacuum pump and push in the air outlet con-
duit. It will engage into its end position on the assem-
bly plate.
► Screw the air outlet conduit on the left and right to the
fixture points shown before.
► You may want to have a flashlight ready to see your
workplace better.
► Fit the spanner wrench provided to the vacuum
pump, as shown in the diagram.
► Adjust the exhaust tube to a length of 120 cm.
► Position the exhaust tube onto the connecting piece
and run the hose along the side of the machine base
and out of the machine.
► Fasten the hose with a hose clamp Ideal Maxi W1
[03090050-xx] to position (1).