00196614-03_AI_Vakuumpumpe_SXDX12_de_en - 第121页
Maintenance 4.1.1 Tools, Consumables, Spar e and Wear Parts Maintenance Tasks for Vacuum Pump Vacuum Pump Vakuumpumpe 121 4 4 M a in t e n a n c e Maintenance See also 3.3.2 Prefitting the Vacuum Pum p [ ➙ 92] 4.1 4 …
Fitting the Vacuum Pump
Final Work 3.5.2 Conversion for C&P12
120 Vacuum Pump Vakuumpumpe
Maintenance
4.1.1 Tools, Consumables, Spare and Wear Parts Maintenance Tasks for Vacuum Pump
Vacuum Pump Vakuumpumpe 121
4
4 Maintenance
Maintenance
See also
3.3.2 Prefitting the Vacuum Pump [ ➙ 92]
4.1
4.1 Maintenance Tasks for Vacuum Pump
Maintenance Tasks for Vacuum Pump
SXDX12V2 The vacuum pum p is an opti on
4.1.1
4.1.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ If needed, filter insert [03077677-xx]
SXDX12V2
▪ Assembly instructions for vacuum pump SX1/SX2 [00196614-xx]
▪ Service manual for your machine
4.1.2
4.1.2 Preparatory Steps
Preparatory Steps
Risk of injury when working near the tap e cutter
► Switch off the machine and secure it to prevent unauthorized reactivation. Observe the instructions
in section "1.2 Preparatory Work..." [ ➙ 73].
► Interrupt the compressed air supply to the machine.
SXDX12V2
► Dismantle the waste slide. Read the service manual for your machine first.
► Dismantle the cover plate over the vacuum pump.
NOTICE
Observe the maintenance instructions!
The following chapters are only excerpts from the maintenance manual.
► Refer to the maintenance manual for your machine if you need complete information about
maintenance for the vacuum pump.
NOTICE
The vacuum pump is an option.
The vacuum pump is located at location 2 behind the COT-insert.
WARNING
Risk of injury when working near the cutter.
When working in the area of the tape cutter, move the component trolley out of the machine
and disconnect the machine from the mains supply and the compressed air supply.
► Wait until the operating pressure has dropped to 0 MPa.
► Always secure the machine against unauthorized reactivation.
► Do not reach into the tape cutter.
CAUTION
Make sure you do not damage any cables and hoses.
CAUTION
Loosened vacuum pump
It is possible to remove the vacuum pump from the machine but it is not necessary.
For a better access, however, it may be useful to loosen the vacuum pump and pull it a bit to
the front within the machine. Also read the Assembly Instructions for the vacuum pump.
► Make sure that the vacuum pump cannot fall out of the machine.
Maintenance
Maintenance Tasks for Vacuum Pump 4.1.3 Recommended maintenance intervals
122 Vacuum Pump Vakuumpumpe
4.1.3
4.1.3 Recommended maintenance intervals
Recommended maintenance intervals
4.1.4
4.1.4 Performing Maintenance Tasks
Performing Maintenance Tasks
SXDX12V2
Maintenance inter-
val
Spare part Task
Every 6 months Filter insert [03077677-xx] Check the filter insert and replace if necessary.
NOTICE
Working life
The filter insert has a working life of at minimum 7500 hours up to 25000 hours. For more infor-
mation about the product life, refer to the manufacturer's documentation (see http://www.beck-
er-international.com – Vacuum pump rotary vane pumps, dry running, type VX4.25)
NOTICE
Observe the manufacturer's instructions
► For more information about maintenance intervals and about how to perform the individual
maintenance tasks, read the manufacturer's instructions for your vacuum pump.
NOTICE
Observe the assembly instructions
► For these tasks, also read the "Assembly instructions SX1/SX2/DX1/DX2" [00196614-xx].