PS288_PS388_PS588_981-0424-002D - 第195页

■ The Vision System ◘ Calibrating The Vision System PS Series Owner’s Manual 4—55 back 4b.4) Click the Camera Calibration tab and repeat from Step 3 Computing Calibration. 5. Finish Part 1— 5a. Click Exit . 5b. Remove th…

Maintenance ■ The Vision System

4—54 Data I/O • 981-0424-002

back

3. Computing Calibration—

3a. Select Grab Calibration Image.

3b. Perform calibration by selecting Compute Calibration.

3c. Select Current.CalibrationImage from the pull-down list and ver-

ify that the majority of the picture is pink. The pink color means

those tiles were used for calibration.

Figure 4-51: This resulting calibration image shows plenty of pink

meaning more than enough tiles were used for calibration.

Note: Ensure no error messages display in the Calibration Info bar

at the bottom of the screen. If error information exists, apply the

message recommendation, and try to calibrate again.

4. Assessing results—

4a. If successful, the green Calibrated message displays in the

lower-left corner of the calibration screen. Save the current

image to the

CameraCalibration.vpp

file by clicking the Save

button, select

CameraCalibration.vpp

, and click Save. When

asked to replace the existing file click OK. Note that the

Camera-

Calibration.vpp

file must be saved from the Camera Calibra-

tion tab.

Note: If you accidentally replace the wrong file, there is folder

named Backup with the original files in them. Copy the desired

backup file to the current working directory.

4b. If NOT successful (there is not much pink color), then repeat

from Step 3 above or make Electronic Vision Adjustments as fol-

lows:

4b.1) Click the Camera Setup tab.

4b.2) Click Electronic Mode (lightning bolt)

4b.3) Adjust the Brightness and Contrast sliders.

■ The Vision System ◘ Calibrating The Vision System

PS Series Owner’s Manual 4—55

back

4b.4) Click the Camera Calibration tab and repeat from

Step 3 Computing Calibration.

5. Finish Part 1—

5a. Click Exit.

5b. Remove the checkerboard target by hand.

Part 2—Updating Vision File Parameters (and then the

Vision File itself)

1. Preparation—

1a. In the Gantry Window, pick up device by moving the probe to

socket 1 of a programmer and right-clicking.

1b. Ensure that the device is centered on the probe.

1c. Click the Go To tab. Click the Go To Vision button.

2. Update vision parameters—

2a. Click the Calibration button to open the Vision Utilities dialog.

2b. Click the Vision Template tab.

2c. Click the Train Parms tab.

2d. From the Algorithm drop-down select PatMax – High Sensitivity.

2e. Ensure that Ignore Polarity is unchecked.

2f. Click Grab Train Image.

2g. Select Current.TrainImage from pull-down menu above the right

camera picture.

2h. Adjust origin of the turquoise X-Y axes as close as possible to the

center of the device. Position the axes by clicking it and drag-

ging.

2i. Adjust the blue search-area rectangle to look similar to the one

in the figure below (roughly: just under the size of the opener).

Click a rectangle handle to resize it.

Maintenance ■ The Vision System

4—56 Data I/O • 981-0424-002

back

Figure 4-52: The Vision Utilities Dialog with Vision Template Tab

selected. After clicking the Grab Train Image button, the Info field

displays results.

3. Training the vision—

3a. Click the Grab Train Image button. Recheck that the X-Y axes

symbol is still centered. If not, adjust it and then click Grab Train

Image again.

3b. Click the Train button.

3c. If the Train function was successful, Trained displays in the

lower-left corner of the screen and no error messages display in

the Info field. If an info message does appear, either create a bet-

ter vision system picture (Getting a Good Picture: Vision System on

page 4-51), or adjust the quality of the current image with bright-

ness/contrast.

Otherwise, if the info says successful click Save. Select your

device-specific vision file (such as TSOP48.VPP) and click Save.

Also, save this image as the

VisionTemplate.vpp

file— Save >

select VisionTemplate.vpp > Save.

3d. Click Exit.

Note: The VisionTemplate.vpp file must be updated every time the

system is recalibrated.

Reteach the Vision Inspection Parameters

1. Teach the Parameters—

1a. Navigate to System > Gantry > Vision System (if you are not

already there).

1b. Click Setup.

VisionTemplate.vpp is the

vision template for all new

vision files. To use it, copy,

paste, and rename it (such

as TSOP48.vpp) when cre-

ating vision files for new

jobs.