PS288_PS388_PS588_981-0424-002D - 第49页
■ Setting Up Input and Output Media ◘ Setting Up Static Tray Input and Output PS Series Owner’s Manual 2—7 back w are, such as Job file, Wi nAH400. ini file, and printer file. These input/output media are described in th…
Setup ■ Setting Up Input and Output Media
2—6 Data I/O • 981-0424-002
back
Note: If electrical or mechanical problems are noted, turn off the
PS System and notify Data I/O Customer Support.
At the Microsoft XP Log-on Window, click the user profile to (usually
labeled MFG to complete the startup procedure).
Figure 2-4: Windows XP Log-on Window.
(Optional) To connect to a network see (Optional) Connecting to a Net-
work on page 2-4.
(Optional) Installing Antivirus Software
The PS System has no antivirus software installed from the factory. It
is highly recommend that customers install their own antivirus soft-
ware. The software should be set to run virus scans manually rather
than at a scheduled time unless you are sure that the PS System will
not be running jobs at that time.
Note: An antivirus program may affect performance.
The PS System runs Windows XP Professional operating system.
Follow instructions for your antivirus software. Contact Data I/O
with specific questions.
Setting Up Input and Output Media
There are many options for device input and output. One option for
input and one for output must be set up on the PS Machine for your
target job. Further, the setup must correspond with the current soft-
■ Setting Up Input and Output Media ◘ Setting Up Static Tray Input and Output
PS Series Owner’s Manual 2—7
back
ware, such as Job file, WinAH400.ini file, and printer file. These
input/output media are described in this section:
•Static Tray (below)
• Automatic Tray Feeder
• Tube Input/Output (vibratory)
• Tape Feeder Input
• Tape Output
Setting Up Static Tray Input and Output
The standard configuration for the PS System is static tray input and
static tray output media. The latest tray mounting configuration uses
a spring-loaded thumb screw for holding the tray in place, while the
earlier configuration uses magnetic angle brackets.
Note: Ensure that blank devices are loaded into the tray with the
correct pin 1 orientation. If pin 1 orientation doesn’t match pin 1
on the sockets, the correct rotation must be taught in the Package
file.
Pin 1 on Data I/O sockets is almost always toward the far side of
the adapter (the back of the PS Machine). Some BGAs and PLCCs
are marked.
Tray Orientation
IF THE TRAY MOUNT IS ORIENTED with the long side parallel to
the Y-axis:
• The input tray goes on the left. Orient the
trays with the beveled corner to the far
left.
IF THE TRAY MOUNT IS ORIENTED with
the long side parallel to the X-axis:
• The input tray goes nearest to the opera-
tor. Trays can be oriented with the bev-
eled corner on the left or right. However,
with Automatic Tray Feeders it must be to the right.
Static Tray Mount with Thumb Screw
To set up the static Thumb Screw Tray input and output:
1. Preparation—
1a. Ensure the PNP head is parked.
1b. Open the front safety shield.
2. Install the Trays—
2a. Set the tray onto the mounting plate inside the indexing blocks.
2b. Use the thumb screw to secure the tray by rotating it 1/2 revolu-
tion past contact with the tray.
Any output media can
be used with any input
media.
Tray mounts can be ori-
ented along the X-axis
or the Y-axis.
Setup ■ Setting Up Input and Output Media
2—8 Data I/O • 981-0424-002
back
Figure 2-5: To remove a tray, unscrew the thumb screw and lift the tray
out. A second method is NOT RECOMMENDED: pulling the thumb screw
back and holding it away from the tray while lifting the tray out; if the
thumb screw is released too soon, devices may be knocked out of the
tray.
Static Tray Mount with Magnets
To set up the static tray input and output with magnetic brackets:
1. Preparation—
1a. Ensure the PNP head is parked.
1b. Open the front safety shield.
2. Install the Trays—
Figure 2-6: Push trays snug against index pins (circled). Extra pins are
for larger trays. Push the magnetic bracket snug against the tray.
2a. Set the tray onto the mounting plate and snug against the index
pins on two sides.
2b. Place the ‘L’ shaped magnetic bracket against the corner adjacent
to the un-indexed sides.