DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第167页

1-145 System Messages of the MMI and Solutions $ab09 The lead size is too large. [Problem]  Occurs when recognizing the lead larg er than the one that can be recognized by the current camera. [Solution]  Recognize the …

100%1 / 200
1-144
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
The threshold value is too low.
The nozzle is severely damaged.
[Solution]
Increase the threshold value on the ‘PCB Edit Part’ of the MMI or check the status of
nozzle.
Please refer to the [Solution] in $a635.
$aa22 There is a problem with threshold. Set the value higher manually.
[Problem]
The threshold value is too low.
The nozzle is severely damaged.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and increase
the threshold value or check the nozzle state in the “Profile Editor”.
Please refer to the [Solution] in $a635.
$ab00 Incorrect angle has been transmitted from the VME.
[Problem]
When incorrect angle has been transmitted from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ab01 Incorrect algorithm number has been transmitted from the VME.
[Problem]
An incorrect algorithm method has been transmitted from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ab02 In the case of checking the heat, the number of lower lead shall be more than two.
[Problem]
In the case of checking the heat, the number of lower lead is one, although it shall be
two.
[Solution]
When the lower lead is in one piece, select the error occurred component in “Part” of
the “PCB Edit” menu, and release if “Heat” is ticked on the ‘Align Data’ of the
“Profile Editor”.
1-145
System Messages of the MMI and Solutions
$ab09 The lead size is too large.
[Problem]
Occurs when recognizing the lead larger than the one that can be recognized by the
current camera.
[Solution]
Recognize the error occurred component using a camera having larger FOV than the
present camera.
$ab0b Width of lead has deviated from the reference size.
[Problem]
Incorrect input of lead width.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu, check the lead
width on the “Profile Editor”, and accurately input the width.
$ab0d Incorrect number of leads.
[Problem]
Incorrect number of leads was inputted.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu, check the
“Lead Num” on the “Profile Editor”, and input the accurate number of leads.
$ab13 Height of component has deviated from the reference size.
[Problem]
Incorrect input of component height.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and enter the
height of the component accurately on the “Profile Editor”.
$ab15 Pitch of upper lead deviated from reference value.
$ab16 Pitch of lower lead deviated from the reference value.
[Problem]
The pitch of the upper lead is different from the reference value.($ab15)
The pitch of lower lead is different from the reference value.($ab16)
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu, check the
“Lead Pitch” on the “Profile Editor”, and input the accurate number of leads.
1-146
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
$ab17 Distance between upper leads deviated from the reference value.
[Problem]
Deviated from the reference value because the upper leads were bent.
[Solution]
Check if the leads of the component are bent.
$ab18 Distance between the lower leads deviated from the reference value.
[Problem]
Deviated from the reference value because the lower leads were bent.
[Solution]
Check if the leads of the component are bent.
$ab19 Angle of the component is deviated from the reference value.
[Problem]
The angle of the component has been rotated too much when picking up the
component.
[Solution]
Perform [Solution] in $aa0b.
$ab1a Angle between the upper leads deviated from the reference value.
[Problem]
Deviated from the reference value because the upper leads ware bent.
[Solution]
Check if the leads of the component are bent.
$ab1b Angle between the lower leads deviated from the reference value.
[Problem]
Deviated from the reference distance because the lower leads were bent.
[Solution]
Check if the leads of the component re bent.
$ab1d An incorrect algorithm number has been input in the internal function.
[Problem]
An incorrect result has been received from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.