DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第173页

1-151 System Messages of the MMI and Solutions  An incorrect result has been received from the VME. [Solution]  T urn of f power to the machine in the usual way . W ait 5 seconds, turn back on and reboot the system. $a…

100%1 / 200
1-150
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
$ac02 Input of incorrect parameter.
[Problem]
Input of the incorrect value of the component parameter.
[Solution]
Check the parameter of the corresponding component on the ‘Part’ of the PCB Edit
menu.
$ac07 The recognized width of the component was different from the reference value.
[Problem]
Incorrect input of the ‘Body X of the component.
The tolerance for H and L of the component was set too low.
The nozzle is contaminated with foreign matter.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu, and check if
the ‘Body X’ at ‘Profile Editor’ has been correctly input.
Select the error occurred component in “Part” of the “PCB Edit” menu, and enter 30%
as the tolerance for each of H and L in the ‘Profile Editor’.
Remove the foreign matter, if any.
Please refer to the [Solution] in $a635.
$ac08 The recognized height of the component was different from the reference value.
[Problem]
Incorrect input of ‘Body Y’ of the component.
oo low setup of the tolerances for H and L of the components.
Foreign matter is in the nozzle.
[Solution]
Perform [Solution] in $ac07.
$ac09 Internal function Error(CenterCorrection).
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac0a Undefined algorithm.
[Problem]
1-151
System Messages of the MMI and Solutions
An incorrect result has been received from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac0b Internal function Error(LineFitting 1).
$ac0c Internal function Error(LineFitting 2).
$ac0d Internal function Error(LineFitting 3).
$ac0e Internal function Error(LineFitting 4).
$ac0f Internal function Error(LineFitting 5).
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac10 The length of lead is too long to recognize.
[Problem]
Inputted sum of upper leads and lower leads is greater than the ‘Body Y’ of the
component.
[Solution]
Input smaller value for ‘Y’ if the ‘L’ value, sum of upper lead and lower lead, is larger
than ‘Body Y’ of the component.
$ac11 The component is set too small or the lead length is set too long.
[Problem]
The inputted lead length(L) of the component is too long.
[Solution]
Set up the lead length(L) of the component to be smaller than the existing value.
$ac12 The width of the component has been recognized to be smaller than the reference
value.
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
1-152
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
$ac13 The width of the component has been recognized to be larger than the reference value.
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac14 The angle of the component has deviated from the reference value.
[Problem]
The Angle of the component has been rotated too much when picking up the
component.
[Solution]
Perform [Solution] in $ab2b.
$ad01 Not a type of the component available for ‘Auto Teach’.
[Problem]
Tried on a type of the component to which the ‘Auto Teach’ function is not supported.
The “Auto Teach” supports CHIP-Rect, TR, TR2, BGA, SOP, SOP2, SOJ, SOJ2, QFP,
PLCC and FLIPCHIP only.
[Solution]
Register manually the components for which ‘Auto Teach’ is not supported.
$ad02 Tangential distance shall be zero for ‘Atuo Teach’.
[Problem]
The ‘Auto Teach’ function is not supported for the component whose tangential
distance is not zero.
[Solution]
Register manually when the tangential distance of the component is zero.
$ad03 The number of leads on one side shall be minimum four for ‘Auto Teach’.
[Problem]
The ‘Auto Teach’ function is not supported for the components having less than four
leads on each side.
[Solution]
Register manually for the components having less than four leads on each side.
$ad04 There shall be no gap when performing the ‘Auto Teach’.
[Problem]