DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第174页

1-152 Advanced Chip Shooter DECAN S2 T roubleshooting Guide $ac13 The width of t he component has b een recognized to be l arger t han the re ference value. [Problem]  An error occurr ed during component recognition. [S…

100%1 / 200
1-151
System Messages of the MMI and Solutions
An incorrect result has been received from the VME.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac0b Internal function Error(LineFitting 1).
$ac0c Internal function Error(LineFitting 2).
$ac0d Internal function Error(LineFitting 3).
$ac0e Internal function Error(LineFitting 4).
$ac0f Internal function Error(LineFitting 5).
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac10 The length of lead is too long to recognize.
[Problem]
Inputted sum of upper leads and lower leads is greater than the ‘Body Y’ of the
component.
[Solution]
Input smaller value for ‘Y’ if the ‘L’ value, sum of upper lead and lower lead, is larger
than ‘Body Y’ of the component.
$ac11 The component is set too small or the lead length is set too long.
[Problem]
The inputted lead length(L) of the component is too long.
[Solution]
Set up the lead length(L) of the component to be smaller than the existing value.
$ac12 The width of the component has been recognized to be smaller than the reference
value.
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
1-152
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
$ac13 The width of the component has been recognized to be larger than the reference value.
[Problem]
An error occurred during component recognition.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ac14 The angle of the component has deviated from the reference value.
[Problem]
The Angle of the component has been rotated too much when picking up the
component.
[Solution]
Perform [Solution] in $ab2b.
$ad01 Not a type of the component available for ‘Auto Teach’.
[Problem]
Tried on a type of the component to which the ‘Auto Teach’ function is not supported.
The “Auto Teach” supports CHIP-Rect, TR, TR2, BGA, SOP, SOP2, SOJ, SOJ2, QFP,
PLCC and FLIPCHIP only.
[Solution]
Register manually the components for which ‘Auto Teach’ is not supported.
$ad02 Tangential distance shall be zero for ‘Atuo Teach’.
[Problem]
The ‘Auto Teach’ function is not supported for the component whose tangential
distance is not zero.
[Solution]
Register manually when the tangential distance of the component is zero.
$ad03 The number of leads on one side shall be minimum four for ‘Auto Teach’.
[Problem]
The ‘Auto Teach’ function is not supported for the components having less than four
leads on each side.
[Solution]
Register manually for the components having less than four leads on each side.
$ad04 There shall be no gap when performing the ‘Auto Teach’.
[Problem]
1-153
System Messages of the MMI and Solutions
The ‘Auto Teah’ function is not supported for the components having missing pins.
[Solution]
Register manually for the components having missing pins.
$ad05 Lead group on one side shall be one for ‘Auto Teach’.
[Problem]
The ‘Auto Teach’ function is not supported for the component having more than two
lead groups on one side.
[Solution]
Register manually the component having more than two lead groups on one side.
$ad06 When performing “AutoTeach”, the number of parameters is different from that of
the lead group, and it cannot be one parameter.
[Problem]
An error occurred due to H/W problem or S/W problem.
[Solution]
Turn off power to the machine in the usual way. Wait 5 seconds, turn back on and
reboot the system.
$ad07 Can not find the end of foot of the(%d)th lead group when performing ‘Auto Teach’
$ad08 Can not find the beginning of the foot of the(%d)th lead group when performing
‘Auto Teach’.
[Problem]
Lighting setup is inadequate.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and check that
illumination is correctly setup in the “Profile Editor”.
Set the background of the component to look dark, and the lead and foot to look bright.
$ad09 Can not find the boundary of foot and lead in the(%d)th lead group when performing
‘Auto Teach’.
[Problem]
The boundary between the lead and foot is not visible when performing the ‘Auto
Teach’.
Lighting setup is inadequate.
[Solution]
Select the error occurred component in “Part” of the “PCB Edit” menu and check that
illumination is correctly setup in the “Profile Editor”.