DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第26页

1-4 Advanced Chip Shooter DECAN S2 T roubleshooting Guide Incorrect feeder base adj ustment E0127 Part wear/distortion in the fee der E0128 S procket, ratchet, etc., are cont aminated with foreign materials. E0129 Incorr…

1-3

System Messages of the MMI and Solutions

 Normal Part Supply

 A pickup error occurred

Cause Description Remarks

Low vacuum

pressure / delayed

vacuum creation

A component of the head’s pneumatic system

is defective

E0100

Vacuum air line is contaminated E0101

Low vacuum pressure due to an oil leak into

the vacuum generator

E0102

Defective contact of the head vacuum solenoid

cable connector

E0102

Defective assembly of the solenoid valve

connector in front of the vacuum generator

E0104

Defective head I/O board E0105

Defective vacuum sensor board E0106

Air leak

s from (Rotary joint, Coil Tube or

Fittings, Vacuum Sensor Board

E0107

Main pneumatic pressure setup error E0108

Blow setup error E0109

Incorrect Vac Delay setup E0110

Pickup position

Error

Incorrect XY coordinates of the pickup point

due to ball spline deformation

E0120

Incorrect setup of the XY coordinates of the

pickup point (Tape, Vibration, Tray Feeder)

E0121

Incorrect tape guide position E0122

Splicing err

or E0123

Incorrect Y position for pickup when installing

tape

E0124

Incorrectly set X coordinate for pickup when

installing tape

E0125

Incorrect pickup position adjustment E0126

1-4

Advanced Chip Shooter DECAN S2 Troubleshooting Guide

Incorrect feeder base adjustment E0127

Part wear/distortion in the feeder E0128

Sprocket, ratchet, etc., are contaminated with

foreign materials.

E0129

Incorrect setup of the part supply position

according to tray shape and part

characteristics

E0130

Incorrect setup of Z and Pick Z values E0131

Foreign materials in the feeder base slot and

clamp

E0132

Incorr

ect Z offset setup E0133

Z Offset change E0134

Problem with

Nozzle

Standard nozzle not used E0140

Damaged nozzle tip, abnormal nozzle spring

tension

E0141

Insufficient nozzle maintenance E0142

Use of nozzle unsuitable for the part E0143

A number of odd

shaped materials

have dropped

Vacuum check setup error E0150

A part dump error

occurred.

Parts are not dumped properly due to incorrect

blow pressure setup

E0160

Cause Description Remarks

1-5

System Messages of the MMI and Solutions

 When parts are picked up properly - Part recognition error [Refer to Section

1.2.1.2]

Cause Description Remarks

Failed to output the

images taken by the

camera

.Defective fly camera or fix camera

.Defective fly camera I/F cable or defective

stage CAM 1 and 2 cables and connections

.Defective Fly Camera PW Sync Exit Cable

and connection

.Defective vision board

.Defective vision I/F board

.Defective camera I/O board (total

destruction of internal chips by fire)

.Defective power supply

.Defective vision board I

F cable and

connection

E0200

Damaged image from

the camera

Unclear image from the

camera

.Defective Fly Cam Sig Ext cable or Fix Cam

signal cable and connection

.Defective camera focus

.Contaminated camera lens and foreign

material on the lens

.Camera dip switch setup error

E0201

Vision processing

timeout /

Failed to recognize the

vision board

.Defective Vision board connection

.Defective SBC

.Defective vision

board

.Defective backplane board

.Damaged vision board driver file due to

infection by virus

E0202

Damage to the mirror .Scratch to the mirror

.Damaged mirror

.Mirror contaminated with foreign material

E0203

Part data registration

error

.Part recognition data registration error

.Recognition parameter setup error

.Illumination setup error

E0204

Defective part The part size is different from that of the

recogniti

on data of the registered part due to

a defective part

E0205