DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第32页
1-10 Advanced Chip Shooter DECAN S2 T roubleshooting Guide tape feede r installed beside it 4) The reel stopper has been damaged or deform ed (only for SM feeders) [Measures] 1) Remove the tape feeder installed in the ri…
1-9
System Messages of the MMI and Solutions
check whether the fuse in the feeder power supply board has a problem. If it is
defective, contact our designated C/S company or local agent before replacing the
fuse.
2) Eliminate the cause of overload or contact our designated C/S or local agent for
appropriate measures.
3) Remove the feeder and reinstall it. If the problem occurs continuously, contact our
designated C/S company or local agent. (Replace the probe pin)
4) Remove the feeder and remove the foreign materials on it. Then reinstall the feeder.
5) Change the feeder base board and check whether it operates properly. Contact our
designated C/S company or local agent.
6) Check whether there are foreign materials on the feeder base board contact. If any,
remove them.
7) Change the feeder control board and check whether it operates properly. Contact our
designated C/S company or local agent.
8) Check whether the feeder control board cable is connected properly. If it has a
problem, contact our designated C/S company or local agent. (Replace the cable)
9) Remove the feeder and then install it again. If this problem occurs continuously,
contact our designated C/S or local agent for appropriate measures.
E0022 The tape feeder cylinder does not operate properly (only for pneumatic SM feeders)
[Cause]
1) Air leaks from the cylinder.
2) Solenoid valve and cylinder works abnormally.
3) Pneumatic pressure is supplied to the cylinder abnormally.
[Measures]
1) Check that if sound of air leakage is heard around the cylinder. If so, contact our
designated C/S company or local agent. (Replace the cylinder.)
2) Check that operation signal is inputted to the solenoid valve properly. If there is any
problem, contact our designated C/S company or local agent. (Replace the solenoid
valve)
3) Check for a bent tube on the pneumatic line as well as air leakage from it.
E0023 Insufficient feeding force of the feeder
[Cause]
1) Check whether the reel width exceeds 13mm and the reel interferes with other feeders
installed nearby
2) The tape reel is not installed properly on the tape feeder hanger (only for SM feeders)
3) A part of the sticker attached to the tape reel has been peeled off, interfering with the
1-10
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
tape feeder installed beside it
4) The reel stopper has been damaged or deformed (only for SM feeders)
[Measures]
1) Remove the tape feeder installed in the right feeder base slot or replace the reel with
the one with a width of less than 13mm.
2) Install the tape reel on the tape feeder hanger properly, referring to the tape feeder
manual.
3) Check the tape reel and remove the cause of the interference.
4) Contact our designated C/S company or local agent. (Replace the reel stopper)
E0024 The feeder spring has been damaged or missing (only for pneumatic SM feeders)
[Cause]
Spring is damaged or slipped out.
[Measures]
Check the spring visually and if it has slipped out, place the spring at the correct
position again. If the spring is extended, contact our designated C/S company or local
agent. (Replace spring)
E0025 A pitch error occurred (only for pneumatic SM feeders)
[Cause]
The sprocket does not rotate as often as designated due to improper adjustment of the
pusher pawl and stop pawl.
The vinyl removal force is excessive according to the part supply state or the sprocket
rotates less than the designated number of times.
The sprocket and ratchet were damaged or worn and therefore they do not rotate as
often as designated.
[Measures]
Contact our designated C/S or local agent.
E0026 Index sensor is defective
[Cause]
1) Index sensor is out of order.
2) Sensor dog or lever is deformed.
[Measures]
1) Check whether an error occurs even when the cylinder operates normally. If so,
contact our designated C/S or local agent.
2) Check whether the lever enters the dog when supplying a part manually. If there is a
1-11
System Messages of the MMI and Solutions
problem, contact our designated C/S or local agent. (Replace sensor dog or lever.)
E0027 A part has not been fed due to insufficient vibration of the vibration feeder
[Cause]
Insufficient vibration of the vibration feeder
[Measures]
Set the position of the vibration diaphragm so that the vibration strength increases
For further details, refer to the following documents:
Technical Reference : Vibration Feeder
E0030 Tape vinyl is twisted inside the tape feeder
[Cause]
Incorrect installation of cover vinyl on the tape guide.
[Measures]
Check whether the upper cover tape is rolled into the tape guide after being peeled off.
If it has a problem, install the tape reel in the tape feeder referring to the tape feeder
manual.
E0031 Defective discharge of tape vinyl
[Cause]
1) Defective tape reel connection
2) There are many foreign materials in the vinyl discharge slot of the tape guide
3) The rear door of the vinyl box does not open smoothly
4) There are many cohesive foreign materials on the vinyl discharge gear
5) Adhesive force of the vinyl itself is particularly strong.
6) Drain spring is damaged or slipped out.
7) Since the vinyl discharge gear bearing has been damaged, it rotates reversely
8) A component of the link is damaged
[Measures]
1) Splice the vinyl using the vinyl splicing tape and tip provided by us. (Refer to the tape
feeder manual)
2) Check and clean the vinyl slot of the tape guide.
3) Contact our designated C/S company or local agent.
4) Clean the vinyl discharge gear.
5) If the adhesive vinyl is not used, or if it is used with the door open, remove the vinyl
inside frequently.