DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第48页
1-26 Advanced Chip Shooter DECAN S2 T roubleshooting Guide Part is placed abnormall y - Abnormal placement error [Refer to Section21.2.2.2 ] Placement Error Det ecti on of de fec ti ve part pick up failed The vac uum…
1-25
System Messages of the MMI and Solutions
1.2.2. Part Placement Error
Parts not picked up - Errors causing parts not to be picked up [Refer to Section 1.2.2.1]
Cause Description
Remark
s
Parts are blown (low
vacuum)
A component of the head’s pneumatic
system is defective
E0300
User parameter setup error (part thickness,
illumination brightness, etc.)
E0301
Excessive fluctuation range of main
pneumatic pressure (4.5 Mpa ~5.5 Mpa)
E0302
In the case of certain model, parts are
blown
E0303
Defective head vacuum solenoid cable
connector
E0304
PCB clamp error E0305
Setup error of the solenoid valve for blow
(strong)
E0306
PCB w
arp A PCB warps up and down E0310
A part adheres to the
nozzle
Setup error of the solenoid valve for blow
(weak)
E0320
Fouled vacuum filter E0321
The head vacuum filter case was not
assembled properly or was damaged
E0322
Defective solenoid valve E0323
The spindle is clogged E0324
Vacuum leaks from the rotary joint E0325
The LED part pickup position is sticky E0326
A large amount of oil entered the vacuum
generator
E0327
Static electric
ity generated E0328
Foreign material was adsorbed at the
nozzle tip
E0329
Part is stuck in the
nozzle
Standard nozzle is not used E0340
A nozzle unsuitable to the part is used E0341
1-26
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
Part is placed abnormally - Abnormal placement error [Refer to Section21.2.2.2 ]
Placement Error
Detection of defective
part pickup failed
The vacuum sensor has a problem. E0150
Defective nozzle check sensor operation
(PIP part)
E0351
Defective side view camera recognition E0352
Defective PCB
sensor
E0360
Cause Description
Remark
s
Defective
placement
accuracy
Bent spindle E0400
Common data setup error E0401
Defective connection of Z-axis driving
system
E0402
The Z-axis motor driver has a problem E0403
The Z-axis LM guide is defective E0404
Distorted part
(placement offset
occurred)
.Calibration has not been performed for a
long period of time. Therefore, offset
occurred to the gantry
.Condition changed according to the site
envir
onment
E0410
After a certain period of time, XY
coordinate distortion occurred in the gantry
working area.
E0411
X and Y limit setup error E0412
Front and rear fiducial camera offsets have
changed
E0413
Offset has changed by being pushed to the
Y-axis
E0414
camera offset has changed E0415
PCB jump E0416
Incorrect nozzle selection E0417
PartR application error E0419
Defective camera assembling E0420
Abnormal R axis dr
iving system E0421
Cause Description
Remark
s
1-27
System Messages of the MMI and Solutions
Incorrect Part Placement
Part Placement on Defective PCB
The Z-axis motor driver has a problem E0422
Influence by
vibration
Influence by X-axis vibration E0430
Influence by Z-axis vibration E0431
Fiducial mark
recognition error
Defective fiducial camera outer illumination E0440
Defective fiducial outer illumination cable
contact
E0441
Impossible to search the fiducial mark
edge
(Fly camera reference mark and mirror are
contaminated)
E0442
Camera dip switch setup er
ror E0443
Fiducial camera illumination setup error E0444
Damaged fiducial mark E0445
Fiducial mark was not used E0446
Placement
coordinate setup
error
Placement coordinate setup error E0450
Array coordinate setup error E0451
Cause Description Remarks
Part flip-over/standing
on edge
The algorithm for reverse insertion
and flip-over of the LED was not used
E0460
The reel is defective. E0461
The tape guide and tape shutter were
changed
E0462
The shutter does not operate properly E0463
Vision system
recognition error
Temporary recognition error of the
vision system
E0470
Cause Description Remarks
Bad mark recognition
error
.Bad mark size error
.Setup is performed so that the
fiducial mark will be recognized
after recognizing the bad mark first
E0480
Cause Description
Remark
s