DECAN_S2_Trouble(Eng_Ver4.2).pdf - 第78页
1-56 Advanced Chip Shooter DECAN S2 T roubleshooting Guide The dif ference in brightness be tween the fiducial mark and its surroundings is less than 20 DN. [Measures] Check the state of the fiducial mark. Adjust t…
1-55
System Messages of the MMI and Solutions
[Cause]
The image is dim or blurred due to incorrect focus.
No difference in brightness between the fiducial mark and its surrounding.
[Measures]
Check the state of the fiducial mark.
Adjust the threshold value or illumination value.
$ae06 Too many fiducial mark candidates
[Cause]
Several fiducial marks exist in one screen.
[Measures]
Adjust the fiducial mark inspection area.
$ae09 Failed to train since the size of the input fiducial is small
[Cause]
The fiducial mark size is less than 100m.
[Measures]
Set the fiducial mark larger than 100m.
$ae10 Failed to train since the size of the input fiducial is very large
[Cause]
The fiducial mark size is greater than 6 mm.
[Measures]
Set the fiducial mark less than 6 mm.
$ae12 The fiducial center was found. However, it has failed to check the final contrast.
[Cause]
1-56
Advanced Chip Shooter DECAN S2 Troubleshooting Guide
The difference in brightness between the fiducial mark and its surroundings is less
than 20 DN.
[Measures]
Check the state of the fiducial mark.
Adjust the illumination value so that the fiducial mark and its surroundings look clear.
$ae15 Cannot find the fiducial mark edge.
[Cause]
There is no fiducial mark.
The difference in brightness between the fiducial mark and its surroundings is small.
[Measures]
Check the state of the fiducial mark.
Adjust the illumination value so that the fiducial mark and its surrounding look clear.
$ae16 The fiducial center was found. However, it is out of the inspection area.
[Cause]
The fiducial mark center is out of the set inspection area.
[Measures]
Adjust the fiducial position or inspection area.
1-57
System Messages of the MMI and Solutions
1.4. Error Code
1.4.1. Classification of Error Codes
Error code Details Note
$0001~$0fff Switch, Machine safety related errors
$1000~$1fff Axis related errors (Includes limit sensor related errors)
$2000~$2fff IO (Sensor input after solenoid operation) related errors Not Used
$3000~$3fff Conveyor related errors (Includes BUT, Hole Fixer, Edge
Fixer)
$4000~$4fff machine operation sequence errors
$5000~$50ff Common Error Related to Feeding Device and Production.
$5100~$51ff Tape Feede
r related errors
$5200~$52ff Stick Feeder related errors
$5300~$53ff Tray Feeder related errors
$5400~$54ff Reserved
$5500~$55ff Tray Feeder communication related errors
$5600~$57ff Reserved
$5800~$58ff Component related errors (component Recognition, Vacuum
related error so on)
Not Used
$5900~$5fff Reserved
$6000~$65ff ANC related errors
$6600~$66ff 3MO related errors Not Used
$6700~$67ff Accessory device related erro
rs
$7000~$8fff Reserved
$9000~$9fff Vision related errors in MMI
$a000~$afff Vision related errors in VME
$b000~$bfff Software debug related errors
$c000~$cfff Motion control related errors
$d000~$d2ff DPRAM communication related errors
$e000~$efff Internal data related errors (Board, MPU Init related Error,
Factory, System DB Error)
$f000~$ffff Internal data related errors (Board, MPU Init related Error,
Factory
, System DB Error)