ASM-X-Spec-SX12V2-EN-DMS - 第28页

28 Component Provision SIPLACE SX1/SX2 Component trolley Component trolley SIPLACE SX The SIPLACE SX compo- nent trolleys are indepe ndent and easily mane uverable modules. The SIPLACE SX machines can accommodate two com…

Smart Pin Support

General

Wide boards tend to deflect

during placement such that,

under certain circumstances,

the components can no lon-

ger be placed with the

desired accuracy. Highly

curved PCBs also affect the

placement accuracy. This

problem can be easily recti-

fied by fitting support pins on

the lifting table.

Smart Pin Support

The support pins are auto-

matically placed on the lifting

table with the help of the

Smart Pin Support option. A

gripper unit is used to pick

the support pins up from spe-

cial magazines and place

them in the prescribed posi-

tions.

Before you place a smart

support pin, the placement

area is cleaned from any

contaminants with a gentle

blast of air. In addition, the

correct position of the sup-

port pins is checked after

placement, with the PCB

camera.

Magazines

There are two different mag-

azines available for auto-

matic changeover to max. 10

support pins in the various

machine configurations.

These magazines are fixed

to a magazine holder and are

fitted to the component trol-

ley docking unit.

Programming

The positions of the support

pins in the machine can be

defined for each board side,

in the SIPLACE Pro Board

Editor.

A 3D diagram of the board

and support pins allows you

to detect and avoid potential

collisions with components,

even during stepped trans-

portation of extra long

boards.

Magazine L 10

Magazine Q 10

Gripper unit

Support pin

Component Provision SIPLACE SX1/SX2

Component trolley

SIPLACE SX

The SIPLACE SX compo-

nent trolleys are independent

and easily maneuverable

modules. The SIPLACE SX

machines can accommodate

two component trolleys, each

with 60 tracks. If a WPC5/

WPC6 is set up at one of the

locations, the other location

can accommodate a compo-

nent trolley with 30 tracks.

The tape reels are taken up

into the tape container of the

component trolley. A cutting

device on the machine auto-

matically cuts the used tape

material. The component

trolleys can be set up directly

on the machine or at an

external setup area with

feeder modules. The benefits

of offline setup are that the

configurations can be pre-

pared without stopping the

line. This allows the setup to

be changed very quickly

using the changeover table

principle. The SIPLACE SX

component trolleys also sup-

port fast setting up and tear-

ing down of feeder modules

even during the placement

process.

The component feeders are

at rest during the placement

process - allowing tapes to

be spliced without stopping

the machine. With the help of

an optional component bar-

code reader and the Setup

Center option, the barcodes

on the tape reels can be read

and checked.

This ensures the correct

assignment of components

to tracks and the traceability

of PCB placement with the

Traceability software.

For safety reasons, unoccu-

pied locations are fitted with

so-called dummy feeder

modules.

Component trolley SIPLACE SX

Tape container

Waste container for remaining

empty tape

Changeover table

Component Provision SIPLACE SX1/SX2

Component trolley

Technical Data

Component trolley dimensions

Component trolley with 60 tracks (length x

width)

Component trolley with 30 tracks (length x

width)

760 mm x 864 mm

760 mm x 471 mm

Height with folded-up handles

900 mm (PCB transport height:

930 mm (PCB transport height:

950 mm (PCB transport height:

934 mm

964 mm

984 mm

Weight of component trolley with 60 tracks

without feeder modules

fully configured with feeder modules

Weight of component trolley with 30 tracks

without feeder modules

fully configured with feeder modules

104 kg

266 kg

76 kg

157 kg

Tape reel diameter

Standard

maximum

up to 432 mm (17")

483 mm (19")

Locations for feeder modules

Component trolley with 60 tracks

Component trolley with 30 tracks

60 feeders with 8 mm

30 feeders with 8 mm

Changeover time for component trolley < 1 minute

Max. component feeding

(2 component trolleys on the SIPLACE SX)

2 component trolleys with tape reel holder and

integral waste bins:

When using a Waffle Pack Changer:

120 locations for feeder modules, each 8 mm.

90 locations for feeder modules, each 8 mm.

Feeder module types (SIPLACE X)

With adapter

Tape feeder modules, reject conveyor, stick mag-

azine and label feeder.

Feeding capacity

(2 component trolleys on the SIPLACE SX)

120 4 mm X feeder modules

120 8 mm X feeder modules

60 tape feeder modules Smart Feeder 2x8 mm X

60 tape feeder modules Smart Feeder 12 mm X

60 tape feeder modules,Smart Feeder 16 mm X

40 24 mm X feeder modules

30 32 mm X feeder modules

24 44 mm X feeder modules

20 56 mm X feeder modules

16 72 mm X feeder modules

12 88 mm X feeder modules