00197684-02_AI_Innenraumbeleuchtung_SX12_de_en - 第29页
Introduction 1.1.4 Safety Instructions for the Power Supply (With SMPS) Safet y Instructions Interior Lighting Innenraumbeleuchtung 29 Maintaining, Installing or Removing Assemblies ► End all placement operations on the …
Introduction
Safety Instructions 1.1.2 Safety Instructions for Working with Strong Magnetic Fields
28 Interior Lighting Innenraumbeleuchtung
1.1.2
1.1.2 Safety Instructions for Working with Strong Magnetic Fields
Safety Instructions for Working with Strong Magnetic Fields
Strong permanent magnet fields
Danger of crushing
Strong permanent magnet fields
1.1.3
1.1.3 Safety Instructions for the Power Supply (Without SMPS)
Safety Instructions for the Power Supply (Without SMPS)
Safety instructions fragment power supply - all machines without X module i.e. all machines except for SX12V2 from N001 and X-series S from H0 01
SXDX12V1V2
▪ This means that some parts of the system carry potentially lethal voltages - even when switched off
at the main power switch.
▪ Incorrect handling of the placement system can therefore result in fatal injuries, severe injuries or
considerable damage to equipment.
▪ Measurements and maintenance work must always be carried out by appropriately qualified person-
nel.
▪ Always follow the applicable accident prevention and DIN regulations (particularly DIN EN 60 204,
part 1) or the regulations specific to your country.
▪ Before starting any maintenance work, switch the machine off at the main switch and disconnect it
from the main power supply.
▪ Always secure the machine against unauthorized reactivation. If these instructions are not followed,
you may be able to touch live parts, which could result in fatal or severe injuries.
DANGER
Strong permanent magnet fields
Fatal hazard: persons with active implants (e.g. pacemakers, defibrillators, insulin pumps etc.)
are at risk from strong permanent magnetic fields inside the machine.
Persons at risk should avoid the immediate vicinity of the machine.
CAUTION
Danger of crushing
Danger of crushing for persons with passive metal implants (e.g. plates, screws).
► Do not reach or lean over into the machine when the protective covers are open.
► Do not bring any metal objects into the hazard area.
CAUTION
Strong permanent magnet fields
There is a risk that the strong magnetic fields could corrupt data on data media or check cards.
► Keep sensitive data supports away from the permanent magnets.
NOTICE
SIPLACE DX1/DX2 and SX1/SX2 to machine no. Mxxx
This section applies to machines of type SIPLACE DX1/DX2 and SX1/SX2 to machine no.
Mxxx without SMPS power supply.
DANGER
Hazardous Voltages!
The machine is supplied with 3 x 400 V~ (or 3 x 204 V~ / 3 x 220 V~ / 3 x 230 V~ / 3 x 380 V~
/ 3 x 415 V~) ± 5 %, 50/60 Hz mains voltages.
► Observe the safety instructions in the user manual during all service work!
► Before you start working on the power supply, check it for absence of voltage and observe
the waiting times!
Introduction
1.1.4 Safety Instructions for the Power Supply (With SMPS) Safety Instructions
Interior Lighting Innenraumbeleuchtung 29
Maintaining, Installing or Removing Assemblies
► End all placement operations on the machine.
► Shut down the Windows operating system correctly, otherwise problems may occur when restarting
or data may be lost.
► Switch the machine off at the main switch.
► Disconnect the machine from the main power supply.
► Switch off the machine and attach warnings signs to indicate that service work is in progress.
1.1.4
1.1.4 Safety Instructions for the Power Supply (With SMPS)
Safety Instructions for the Power Supply (With SMPS)
Safety instructions fragment power supply - all machines with X module i.e. all machines except for SX12V2 from N001 and X-series S from H001
SX12 V2
Residual voltages and discharge times in the machine
If the emergency stop button is pressed or the placement system is switched off, the 300 V~ link voltage
for the gantry axes and the 160 V~ link voltage for the star axes are reduced to harmless residual volt-
ages in a very short time.
NOTICE
SIPLACE SX1/SX2 V2 from machine no. N001 upwards
This section applies to machines of type SIPLACE SX1/SX2 V2 from machine no. N001 with
SMPS power supply.
DANGER
Dangerous voltages!
The machine is supplied with 3 x 360 V~ to 3 x 480 V ± 10 %, 50/60 Hz or optional with 3 x 200
V~ to 3 x 240 V~ ± 10 %; 50/60 Hz mains voltage. This means that some parts of the system
carry potentially lethal voltages - even when it is switched off at the main power switch and the
power plug is unplugged.
Incorrect handling of the placement system can result in death or severe injury or considerable
damage to equipment.
► Always follow the applicable accident prevention and DIN regulations (particularly EN
60204, part 1 or IEC 60204, part 1) and the applicable regulations in your own country.
► The covers of the power supply unit must ONLY be opened by appropriately qualified and
trained personnel.
► Observe the safety instructions in the user manual during all service work!
► Before you start working on the power supply, check it for absence of voltage and observe
the waiting times!
Introduction
Safety Instructions 1.1.4 Safety Instructions for the Power Supply (With SMPS)
30 Interior Lighting Innenraumbeleuchtung
Energy state of the machine after switching off at the main power switch
Placement system switched off at the main switch, but still connected
SX12 V2
DANGER
Hazardous voltages in the power supply unit!
The power supply unit houses components (capacitors) that can carry hazardous voltages for
about 5 minutes after the machine has been switched off and the power plug has been un-
plugged.
► Wait at least 5 minutes before your start working on the power supply unit.
► Work on the power supply and the contactor safety breaker (CSB) must only be carried out
by service engineers of ASM Assembly Systems GmbH & Co. KG or by machine owner ser-
vice engineers who have been trained by ASM.
CAUTION
Loss of data!
To avoid losing data, assess the following criteria before switching off your automatic place-
ment system (apart from in emergencies):
► Has the placement system finished transmitting machine, setup and panel data?
► Has the placement system finished processing the PCB?
► Has the placement system completed the run-up phase?
DANGER
Risk of death by voltages!
Incorrect handling of the placement system can result in death or severe injury or considerable
damage to equipment.
The following components still carry potentially lethal voltages on the power supply even if the
main power switch is switched off:
► Main power supply cable connection terminals
► L1, L2, and L3 of the main switch S1
► Service socket X98
► Contactor safety breaker (CBS) still carries voltage for 5 minutes after switching off at the
main switch.
► The color of all individual wires which still carry potentially lethal voltages even if the main
power switch is switched off is orange.
Front of power supply unit (SX1/SX2, SMPS)
1. Main switch (S1)
2. Service socket (X98)
3. Main power supply cable connection terminals (X94)
for the power supply cable