N7201A616E00_0317 - 第696页
NPM-W 2 EJM7DE-MB-09O -00 9-1-6 -13 Specifi- cation No zzle specifica tions 7 Dispensing nozzle (option) 3 Operating procedure 9-1-6 2) 2-point nozzle (Unit ： mm) Dispensing disabled area 3.4 Dispensing disabled area 3.4…
NPM-W2 EJM7DE-MB-09O-00
9-1-6-12
Dispensing direction
0° -90° 90°
1-point dispensing /
Drawing dispensing
*1)
4.9 5.65 4.1
2-point dispensing 4.9 (Partially 5.4) 5.65 5.63
4-point dispensing 4.9 5.9 5.9
■Restriction of dispensing area
Dispensing disabled area from the PCB edge (PCB top surface; rear side) (Y-direction) (Unit：mm)
●In the case of the near side of the PCB undersurface, because the stopper position is inverted in Y-
direction, the values for -90° switch places with those for 90° in the above table of dispensing
disabled distances.
*1) The drawing dispensing nozzle is the same condition as “0°” of the 1-point nozzle.
1) 1-point nozzle / Drawing dispensing nozzle
*2)
(Unit：mm)
( 0°)
Dispensing disabled area
3.4
4.9
( -90°)
Dispensing disabled area
3.4
5.65
(90°)
Dispensing disabled area
3.4
4.1
Stopper edge
PCB edge
Stopper tip
4.1
5.65
4.9
Dead space
3.4
( 0°)( -90°)
(90°)
Nozzle
At
a glance
NPM-W2 EJM7DE-MB-09O-00
9-1-6-13
Specifi-
cation
Nozzle specifications 7
Dispensing nozzle (option) 3
Operating procedure
9-1-6
2) 2-point nozzle (Unit：mm)
Dispensing
disabled area
3.4
Dispensing
disabled area
3.4
5.4
5.65
( 0°)( -90°, 90°)
( 0°)
PCB edge
5.65
4.9
Dead space
3.4
Stopper tip
Nozzle
3.65 (7223)
3.8 (7222)
3.9 (7236)
4.0 (7201,7204)
4.1 (7202)
( -90°, 90°)
①7224 nozzle
PCB edge
5.65
5.4
Dead space
3.4
Stopper tip
Nozzle
4.4
Dispensing
disabled area
3.4
Dispensing
disabled area
3.4
4.9
5.65
( 0°)( -90°, 90°)
3) 4-point nozzle (Unit：mm)
②Other nozzles
( 0°)
PCB edge
5.9
4.9
Dead space
3.4
Stopper tip
Nozzle
( -90°, 90°)
4.4
3.9 (7601)
4.3 (7606)
Dispensing
disabled area
3.4
Dispensing
disabled area
3.4
4.9 5.9
( 0°)( -90°, 90°)
●The dispensing disabled area applies when mark recognition offset and nozzle offset are 0.
If correction or nozzle offset is performed the dispensing disabled area may be wider.
NPM-W2 EJM7DE-MB-09O-00
9-1-7
Nozzles are compatible between the nozzles for the NPM 3-nozzle head and those for CM301/ CM202/
CM120/ CM100 by replacing orifices, or attaching or detaching new ones.
●Nozzles for AM100 are not available.
■Divided-type nozzles
(1001, 1002 nozzle)
■Integral-type nozzle
(1003,1004,1005, special nozzle)
■Divided-type nozzles
(1001, 1002 nozzles)
■Integral-type nozzle
(1003,1004,1005, special nozzle)
Orifices C
(KXFB03KPA00)
Dedicated orifices B
(KXFB03KNA00)
Specifi-
cation
Compatibility among
nozzles
Orifices A
(KXFB01MPA00)
Orifices A Orifices B
Orifices C
CM301
CM202
CM120
CM100
Operating procedure
9-1-7
CM101 CM212
CM232 CM400
CM401 CM402
CM602 DT401
NPM series
At
a glance