DFD6361-Maintenance - 第706页
Appendix-1 CHECK SHEET 1 - MAINTENANCE AND PERIODIC INSPECTION - Check sh eet for maint enance and perio dic inspecti on Use the following form when per forming maintenance and periodic inspe ction. * ) Decide t he prope…
ÿ
ÿ
ÿ
G-5
SECTION 9. PHYSICALAND CHEMICAL PROPERTIES
APPEARANCE AND ODOR Brown color, butter-like, mild odor
DENSITY (g/cm
3
)at15°C. About 0.9
SOLUBILITY IN WATER. Negligible
MELTING POINT °C. NA
DROPPING POINT °C. Above 200
BOILING POINT. NA(Not applicable)(High)
SECTION 10. STABILITY AND REACTIVITY
STORAGE STABILITY. This product is stable under normal storage.
INCOMPATIBILITY. Strong oxidizing agents.
DECOMPOSITION PRODUCTS. Carbon oxides, Sulfur oxides, Phosphorous compounds, etc.
POLYMERIZATION. Will not occur.
FLASH POINT (METHOD USED) °C. 201(Seta Close Cup)
SECTION 11. TOXICOLOGICAL INFORMATION
ACUTE TOXICITY Inhalation No data as product
Oral No data as product
CORROSIVE AND IRRITANT PROPERTIES. If prolonged or repeated skin contact occurs, may
cause skin irritation.
If eye contact occurs, may cause eye irritation.
SECTION 12. ECOLOGICAL INFORMATION
No known ecological data.
SECTION 13. DISPOSAL CONSIDERATION
Waste must be disposed of in accordance with federal, state and local environment control
regulations.
SECTION 14. TRANSPORT INFORMATION
Keep away from oxidizing materials and source of ignition.
Japan Fire Protection Law. Non dangerous substance.
UN Recommendations on the Transport of Dangerous Goods. Non dangerous substance.
Follow all regulations in your country.
SECTION 15. REGULATION INFORMATION
Follow all regulations in your country.
SECTION 16. OTHER INFORMATION
REFERENCES.
1) ARC MONOGRAPHS ON THE EVALUATION OF THE CARCINOGENIC RISK OF CHEMICALS
TO HUMANS VOLUME 33
2) Material Safety Data Sheet guidebook(English)(Japan Chemical Industry Association Information
Center)
This Material Safety Data Sheet was prepared on the basis of materials' information, and data
obtained at present by our company. To the best of our knowledge, the information contained here in is
accurate.
Final determination of suitability of all material is the sole responsibility of the user.
All materials may present unknown hazards and should be used in caution.
The information herein is given in good faith, but no warranty express or implied, is made.
Appendix-1
CHECK SHEET 1 - MAINTENANCE AND PERIODIC INSPECTION -
Check sheet for maintenance and periodic inspection
Use the following form when performing maintenance and periodic inspection.
*
) Decide the proper intervals for maintenance considering the
machine usage conditions and fill out here.
Interval Refer To Inspection/Maintenance Item Inspection/Maintenance Date
Every Day
Section Airsupplypressure // // // // //
E-2 Stainsonthesafetylabels // // // // //
Airspindleaxisrotation // // // // //
Scratchesandsoilingontheflange // // // // //
Soilinganddamageonthechucktable // // // // //
That the work being taken over properly / / / / / / / / / /
Abnormal noise or vibration during spindle rotation / / / / / / / / / /
Splash cover and arm section cover status during spindle
rotation
// // // // //
Splash cover and arm section cover status during spinner table
rotation
// // // // //
ZEMsequence //////////
EMO switch activation / / / / / / / / / /
Checking the spinner high-pressure pump pressure / / / / / / / / / /
7-Day Intervals
E-3 Cleaningthecuttingroom // // // // //
30-Day Intervals
E-4 Flangeconditioning // // // // //
Cleaningthedraintank //////////
183-Day Intervals
E-5 Hub mount conditioning / / / / / / / / / /
Greasing the elevator axis / / / / / / / / / /
Greasingtheframecenteringaxis // // // // //
Cleaningthespindlecoolingwaterpath // // // // //
365-Day Intervals
E-6 Cleaning the vacuum ejector / / / / / / / / / /
GreasingtheX-axis // // // // //
Greasingthepush-pullaxis //////////
Cleaning the upper arm guide / / / / / / / / / /
Appendix-2
Check sheet for maintenance and periodic inspection (Continued)
Interval Refer To Inspection/Maintenance Item Inspection/Maintenance Date
365-Day Intervals
E-6 Greasing the lower arm guide / / / / / / / / / /
(Continued)
Greasing the θ-axis sensor assembly section
// // // // //
GreasingtheY-axis // // // // //
GreasingtheZ-axis // // // // //
*
E-1 Cleaning the non-contact setup sensor / / / / / / / / / /
Cleaning the blade breakage detector sensor / / / / / / / / / /
Cleaningthespindle //////////
Cleaningthetouchpanel // // // // //