DFD6361-Maintenance - 第707页
Appendix-2 Check sh eet for maint enance and perio dic inspecti on (Contin ued) Inte rval Refer To Inspection/Maintenance Item Inspection/Maintenance Date 365-Day Intervals E-6 Greas ing the lower arm guide / / / / / / /…
Appendix-1
CHECK SHEET 1 - MAINTENANCE AND PERIODIC INSPECTION -
Check sheet for maintenance and periodic inspection
Use the following form when performing maintenance and periodic inspection.
*
) Decide the proper intervals for maintenance considering the
machine usage conditions and fill out here.
Interval Refer To Inspection/Maintenance Item Inspection/Maintenance Date
Every Day
Section Airsupplypressure // // // // //
E-2 Stainsonthesafetylabels // // // // //
Airspindleaxisrotation // // // // //
Scratchesandsoilingontheflange // // // // //
Soilinganddamageonthechucktable // // // // //
That the work being taken over properly / / / / / / / / / /
Abnormal noise or vibration during spindle rotation / / / / / / / / / /
Splash cover and arm section cover status during spindle
rotation
// // // // //
Splash cover and arm section cover status during spinner table
rotation
// // // // //
ZEMsequence //////////
EMO switch activation / / / / / / / / / /
Checking the spinner high-pressure pump pressure / / / / / / / / / /
7-Day Intervals
E-3 Cleaningthecuttingroom // // // // //
30-Day Intervals
E-4 Flangeconditioning // // // // //
Cleaningthedraintank //////////
183-Day Intervals
E-5 Hub mount conditioning / / / / / / / / / /
Greasing the elevator axis / / / / / / / / / /
Greasingtheframecenteringaxis // // // // //
Cleaningthespindlecoolingwaterpath // // // // //
365-Day Intervals
E-6 Cleaning the vacuum ejector / / / / / / / / / /
GreasingtheX-axis // // // // //
Greasingthepush-pullaxis //////////
Cleaning the upper arm guide / / / / / / / / / /
Appendix-2
Check sheet for maintenance and periodic inspection (Continued)
Interval Refer To Inspection/Maintenance Item Inspection/Maintenance Date
365-Day Intervals
E-6 Greasing the lower arm guide / / / / / / / / / /
(Continued)
Greasing the θ-axis sensor assembly section
// // // // //
GreasingtheY-axis // // // // //
GreasingtheZ-axis // // // // //
*
E-1 Cleaning the non-contact setup sensor / / / / / / / / / /
Cleaning the blade breakage detector sensor / / / / / / / / / /
Cleaningthespindle //////////
Cleaningthetouchpanel // // // // //
Appendix-3
CHECK SHEET 2 - CONSUMABLE PARTS REPLACEMENT -
Check sheet for consumable parts replacement
Use the following form when replacing consumable parts.
*
) Decide the proper intervals for maintenance considering the machine usage
conditions and fill out here.
Interval Refer To Inspection/Maintenance Item Inspection/Maintenance Date
365-Day Intervals
F-1 Air filter
// // // // //
Halogen lamp
// // // // //
Spindle carbon brush
// // // // //
Spray tip of spinner section
// // // // //
Vacuum pad for the upper arm section
// // // // //
Vacuum pad for the lower arm section
// // // // //
Y-axis roll sheet
// // // // //
700-Day Intervals
F-2 Spindle coolant water flow rate sensor
// // // // //
Solenoid valve
// // // // //
1000-Day Intervals
F-3 Bellows
// // // // //
θ-axis waterproof cover
// // // // //
θ-axis O-ring
// // // // //
θ-axis V-ring
// // // // //
Chuck table center ring
// // // // //
Spinner table O-ring
// // // // //
1800-Day Intervals
F-4 Flowmeter
// // // // //
*
F-5 Spinner high-pressure pump consumable parts
// // // // //
Fluorescent lamp
// // // // //
UV irradiation lamp
// // // // //
Controller of the wheel coolant water
// // // // //
-
Microscope LED light
// // // // //
Hard disk drive
// // // // //
Contact your
nearest
DISCO office.
Circuit board of the electrical system
// // // // //