SIPLACE D4-D4i 工程师手册_EN - 第9页

Introduction 1.1.1 Serial Number of D4 Module Module Description Service Manual SIPLACE D4/D4i 9 1 1 I n t r o d u c t io n Introduction This service guide is a manual or reference work f or performing service w ork on t…

100%1 / 248
Contents
8 Service Manual SIPLACE D4/D4i
6.5.1.1 Measuring Points and Belt Tensions for D4 Conveyor 226
6.5.2 Setting the fixed conveyor side (single and dual conveyor) 226
6.5.2.1 General Notes 226
6.5.2.2 Widening the Conveyor (Flexible Dual Conveyor for Single Conveyor Mode) 227
6.5.2.3 Connecting the Dual Conveyor Lifting Tables 228
6.5.2.4 Converting the Single Conveyor Mode Back to Flexible Dual Conveyor Mode 228
6.5.3 Moving the Fixed Conveyor Edge for ’Extra Wide Conveyor’ 228
6.5.4 Checking the Limit Switch Position 229
6.5.4.1 Adjusting the Limit Switch for Initializing the Adjustment Unit 230
6.5.5 Width Adjustment Unit 230
6.5.5.1 Setting the Proximity Switch on the Adjustment Unit 230
6.5.5.2 Setting the Pneumatic Cylinder Proximity Switch on the Adjustment Unit 231
6.5.6 Setting the Laser Light Barrier for the Stopper Position 231
6.5.7 Function "Constant Transport Time in Placement Area" 233
6.5.8 Light Barrier Functions in Input, Intermediate and Output Conveyors 233
6.5.9 Setting the Clamping Actuator 234
6.5.10 Board Clamping Functions 234
6.5.10.1 Setting Board Clamping 235
6.5.10.2 Setting the Board Clamping 236
6.5.11 Lifting Table Functions 238
6.5.11.1 Adjusting the Speed of the Lifting Table (from SW 602) 239
6.5.11.2 Setting the Lifting Table Unit [00358684-05] 240
6.5.12 Conveyor Control TSP 301 241
6.5.12.1 Jumper Settings for TSP 301 241
6.5.12.2 Conveyor Control TSP 301 with Siemens Interface 242
6.5.12.3 LED Display on Conveyor Control TSP 301 243
6.5.12.4 Assignment Table: LEDs on the TSP 301 Conveyor Control 243
6.5.12.5 Siemens/SMEMA TSP 301 Interface Description 246
Introduction
1.1.1 Serial Number of D4 Module Module Description
Service Manual SIPLACE D4/D4i 9
1
1 Introduction
Introduction
This service guide is a manual or reference work for performing service work on the SIPLACE® D4
placement machines.
1.1
1.1 Module Description
Module Description
1.1.1
1.1.1 Serial Number of D4 Module
Serial Number of D4 Module
1.1.2
1.1.2 Environmentally-Friendly Disposal of Materials and Components
Environmentally-Friendly Disposal of Materials and Components
SIPLACE products are manufactured using only materials and parts that can be easily separated and
disposed of in an environmentally-friendly way. Hazardous materials are not necessary for the installa-
tion, dismantling or operation of the machine.
1.1.3
1.1.3 Use of Original SIPLACE Accessories and Spare Parts
Use of Original SIPLACE Accessories and Spare Parts
Only use original spare parts and authorized accessories. The use of other parts will affect safety and
will invalidate the liability for any consequential damage.
1.2
1.2 Key Information
Key Information
1.2.1
1.2.1 Information About This Service Manual (Customer Version)
Information About This Service Manual (Customer Version)
The service work described in this manual may only be performed by specially trained service techni-
cians, with appropriate qualifications and expertise.
If you should have any questions during the service work, please contact the SIPLACE customer hotline
directly:
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the operating manual of the according machine
for all service work!
The serial number of your placement machine can be
found on the typeplate (1).
NOTICE
The company operating the system has sole responsibility for the proper, environmentally-
friendly disposal of machines, working materials, consumables and wear parts.
► Please observe your national statutory provisions for waste disposal and environmental
protection.
Introduction
Key Information 1.2.2 Validity of Document
10 Service Manual SIPLACE D4/D4i
(0049) 089 20800 48642
or send an e-mail to: hotline.siplace@siemens.com.
1.2.2
1.2.2 Validity of Document
Validity of Document
This document contains instructions about the service work for all D3 machines from the SIPLACE D
series.
The service work is listed on a module by module basis:
▪ If the work required for specific machines should differ from the standard procedure, this will be in-
dicated with reference to the machine number, series and various delivery statuses.
▪ Diagrams should be seen as examples e.g. the diagram of a machine with different paint finish does
not mean that the following information only applies to the machine type shown.
The main focus of this manual is on a description of mechanical service work.
Please refer to the circuit diagram folder supplied with your machine for any electrical checks:
▪ Siplace D3 circuit diagram folder, item no. 00195091-xx (German and English)
1.2.3
1.2.3 Release History
Release History
1.2.4
1.2.4 Further Information
Further Information
If you have any questions about this manual or if you would like more information about certain subjects,
please contact your local Siemens branch or us directly:
Siemens Electronics Assembly Systems
Rupert-Mayer-Strasse 44
81379 Munich, Germany
Tel.: +49 (89) 20800 – 27819
Fax: +49 (89) 20800 – 36692
E-mail: siplace.de@siemens.com
1.2.5
1.2.5 SIPLACE on the World Wide Web (WWW)
SIPLACE on the World Wide Web (WWW)
Log into our SIPLACE® homepage at http://www.siplace.com.
► Select either the German or English version.
The different sections contain information about our products, services and contact persons.
In addition, registered customers can access the
SIPLACE User Group
. Here you can call up special
information about our placement systems e.g.
▪ Technical documentation,
▪ Technical information,
▪ Spare parts lists etc.
Registration for the user group is very simple:
► Click on the Register link.
► Fill in the registration form and send it off to us.
Soon afterwards, you will receive your access authorization with USER ID and password.
Release Changes
07/2007
(initial release)
(After data migration)
08/2008 Corrected version
Revision of the C&P and Twin Head chapters
11/2013 Corrected version
Revision of the PCB conveyor system chapter