DECAN_S1_Troubleshooting_Guide(Eng_Ver1.3)_Print_Web.pdf - 第31页

1-7 System Messages of the MMI and Solutions 1.2.1.1. Part N on-pickup Error E0000 Incorrect installation of tape reel in the tape feeder [Cause]  Sprocket teeth of the tape feeder are not engaged correctly into the tap…

1-6

Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide

Camera recognition

timeout error / Vision

processing timeout

error

.Defective vision board

.Defective Vision board connection

E0206

Fiducial camera noise

(Occurrence of

distorted image, half

image, overlapped

image, etc.)

.Defective Fiducial Camera cable

connection

.Defective fiducial camera

.Defective vision board I/F

E0207

Defective camera

assembling

The camera recognition area is not located

at the part center but slightly offset in the X-

axis or Y-axis direction

E0208

The image from the

camera is dark

Abnormal illumination

brightness

.Defective camera illumination board

(Defective outer illumination board)

.Defective head illumination board

.The illumination LEDs turn on and off

repeatedly due to defective contact of the

cable related to the lighting

.Light mapping error

E0209

Contaminated nozzle E0211

Defective recognition

of 'Ref' mark on the

head

Contaminated 'Ref' mark on the head E0212

Cause Description Remarks

1-7

System Messages of the MMI and Solutions

1.2.1.1. Part Non-pickup Error

E0000 Incorrect installation of tape reel in the tape feeder

[Cause]

 Sprocket teeth of the tape feeder are not engaged correctly into the tape holes.

[Measures]

 Engage the sprocket teeth of the tape feeder into the tape holes correctly.

E0010 A part is flipped over or stands on an edge

[Cause]

1) When peeling the upper cover tape manually, parts are taken out being attached with

the vinyl Emboss tape reel is used for an 8mm and 4 pitch feeder that uses paper tape

reel

2) Emboss tape reel is used for an 8mm 4 pitch feeder that uses a paper tape reel.

[Measures]

1) Replace the tape reel.

2) For an emboss tape reel, use an emboss tape feeder.

E0011 A part is stuck to the tape guide (only for 8mm feeder)

[Cause]

 Static electricity occurred to a part or a part is stuck to the tape guide since it was

magnetized

[Measures]

 Contact our designated C/S company or local agent. (Replace the tape guide)

For further details, refer to the following documents:

Technical Reference : Tape Feeder

E0012 A part is flipped over or stands on an edge due to deformation of the tape guide and

shutter

[Cause]

1) The tape guide does not move smoothly or it is deformed due to impact

2) When supplying parts manually, a part interferes with the shutter

[Measures]

1) Contact our designated C/S company or local agent. (Replace the tape guide)

2) Contact our designated C/S company or local agent. (Replace the shutter)

1-8

Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide

E0013 A part is flipped over or stands on an edge due to defective shutter operation

[Cause]

 The shutter does not operate smoothly due to defective tape guide

[Measures]

 Contact our designated C/S company or local agent. (Replace the tape guide)

E0014 A part is flipped over or stands on an edge due to inappropriate part feeding speed

(for feeders larger than 12mm SMF and SLM feeders)

[Cause]

 Check whether the speed control valve is set in the low part feeding speed mode for

the feeder cylinder (for feeders larger than 12mm feeders)

 Check whether a part is not flipped over or stands on an edge by controlling the

feeding speed of the feeder using the speed control valve

[Measures]

 Control the part feeding speed to an appropriate speed using the speed control valve

E0020 Defective feeding due to foreign materials on the sprocket and ratchet

[Cause]

 Defective maintenance of the tape feeder

[Measures]

 Remove the foreign materials on the sprocket and ratchet

E0021 Defective feeding motor operation of the tape feeder (for SME and SLM feeders)

[Cause]

1) Abnormal power supply to the motor (defective fuse in the feeder power supply board)

2) The LED color changes to red due to overload and the motor does not operate

3) Defective probe pin

4) Foreign materials exist on the probe pin

5) The feeder base is damaged or defective

6) Foreign materials exist on the feeder base board contact

7) Defective feeder control board

8) Defective feeder control board cable

9) Any of the 7 segment errors occurred (E0: Overcurrent error, E1: Origin sensor error,

E6: Pitch counter error).

[Measures]

1) Check whether the power is supplied to the motor properly. If there is a problem,