DECAN_S1_Troubleshooting_Guide(Eng_Ver1.3)_Print_Web.pdf - 第35页
1-11 System Messages of the MMI and Solutions problem, contact our designated C/S or local agent. (Replace sensor dog or lever .) E0027 A part has not been fed due to insu fficient vibration of the vibration feeder [Caus…
1-10
Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide
tape feeder installed beside it
4) The reel stopper has been damaged or deformed (only for SM feeders)
[Measures]
1) Remove the tape feeder installed in the right feeder base slot or replace the reel with
the one with a width of less than 13mm.
2) Install the tape reel on the tape feeder hanger properly, referring to the tape feeder
manual.
3) Check the tape reel and remove the cause of the interference.
4) Contact our designated C/S company or local agent. (Replace the reel stopper)
E0024 The feeder spring has been damaged or missing (only for pneumatic SM feeders)
[Cause]
Spring is damaged or slipped out.
[Measures]
Check the spring visually and if it has slipped out, place the spring at the correct
position again. If the spring is extended, contact our designated C/S company or local
agent. (Replace spring)
E0025 A pitch error occurred (only for pneumatic SM feeders)
[Cause]
The sprocket does not rotate as often as designated due to improper adjustment of the
pusher pawl and stop pawl.
The vinyl removal force is excessive according to the part supply state or the sprocket
rotates less than the designated number of times.
The sprocket and ratchet were damaged or worn and therefore they do not rotate as
often as designated.
[Measures]
Contact our designated C/S or local agent.
E0026 Index sensor is defective
[Cause]
1) Index sensor is out of order.
2) Sensor dog or lever is deformed.
[Measures]
1) Check whether an error occurs even when the cylinder operates normally. If so,
contact our designated C/S or local agent.
2) Check whether the lever enters the dog when supplying a part manually. If there is a
1-11
System Messages of the MMI and Solutions
problem, contact our designated C/S or local agent. (Replace sensor dog or lever.)
E0027 A part has not been fed due to insufficient vibration of the vibration feeder
[Cause]
Insufficient vibration of the vibration feeder
[Measures]
Set the position of the vibration diaphragm so that the vibration strength increases
For further details, refer to the following documents:
Technical Reference : Vibration Feeder
E0030 Tape vinyl is twisted inside the tape feeder
[Cause]
Incorrect installation of cover vinyl on the tape guide.
[Measures]
Check whether the upper cover tape is rolled into the tape guide after being peeled off.
If it has a problem, install the tape reel in the tape feeder referring to the tape feeder
manual.
E0031 Defective discharge of tape vinyl
[Cause]
1) Defective tape reel connection
2) There are many foreign materials in the vinyl discharge slot of the tape guide
3) The rear door of the vinyl box does not open smoothly
4) There are many cohesive foreign materials on the vinyl discharge gear
5) Adhesive force of the vinyl itself is particularly strong.
6) Drain spring is damaged or slipped out.
7) Since the vinyl discharge gear bearing has been damaged, it rotates reversely
8) A component of the link is damaged
[Measures]
1) Splice the vinyl using the vinyl splicing tape and tip provided by us. (Refer to the tape
feeder manual)
2) Check and clean the vinyl slot of the tape guide.
3) Contact our designated C/S company or local agent.
4) Clean the vinyl discharge gear.
5) If the adhesive vinyl is not used, or if it is used with the door open, remove the vinyl
inside frequently.
1-12
Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide
6) Check for the spring visually and if it is slipped out, place the spring at the right
position again. If the spring is damaged or deformed, contact our designated C/S
company or local agent.
7) Contact our designated C/S company or local agent. (Replace the bearing of the vinyl
discharge gear.)
8) Contact our designated C/S company or local agent. (Replace link)
E0040 A part is stuck in the tape discharge path.
[Cause]
Foreign materials exist on the tape discharge path
[Measures]
After lifting the locker sufficiently while pressing the locker limit pin, correct the
carrier tape and return the locker to the normal position.
E0050 Pickup Z setup error occurred.
[Cause]
Pickup height setup is incorrect.
[Measures]
Adjust the pickup Z height and pickup speed.
E0051 The down movement for pickup is fast.
[Cause]
The part to be placed using the Soft Touch function was placed in the high speed
mode.
[Measures]
Set the Soft Touch function and use it.
E0100 Vacuum Sensor Board The vacuum pressure of the head’s pneumatic system is low
due to a defective component
[Cause]
1) Defective solenoid valve
2) Defective Vacuum Pump (Applied only to the SM471, 481, DECAN F2 machine.)
3) Damaged tube and fitting
[Measures]
1) Perform solenoid valve operation test. If a problem occurs, contact our local agent.
(Replace the solenoid valve.)
2) Check whether the vacuum level of the front vacuum gauge is -90kPa. If a problem
occurs, contact or our local agent. (Replace the Vacuum Pump.)