DECAN_S1_Troubleshooting_Guide(Eng_Ver1.3)_Print_Web.pdf - 第40页
1-16 Next Generation, Multi-Functional Plac er DECAN S1 Troubleshooting Guide [Measures] Remove the part or foreign materials. E0125 The X part feeding position is in correct due to a problem with the feeder [Cause] …
1-15
System Messages of the MMI and Solutions
E0120 The XY coordinates of the corresponding spindle center become incorrect due to a
deformed ball spline
[Cause]
Deformed ball spline
[Measures]
Check the run-out state of the ball spline after removing the nozzle holder. If
necessary, reassemble the ball spline or perform calibration. Contact our designated C/
S company or local agent. (Replace ball spline )
E0121 Incorrect setup of the XY coordinates of the pickup point
[Cause]
Incorrect pickup position setup in the 'Feeder' menu of the MMI
[Measures]
Teach the part pickup position of the feeder again.
E0122 Incorrect tape guide position causes interference during feeding
[Cause]
1) The tape guide is not secured correctly with a locker.
2) There is foreign material on the vinyl contact surface of the tape guide.
3) The tape guide is deformed due to collision or is worn out.
[Measures]
1) Secure the tape guide with locker correctly
2) Clean the tape guide periodically.
3) Contact our designated C/S company or local agent for proper measures.
E0123 The part feeding position becomes incorrect due to incorrect tape splicing caused by
a splicing error
[Cause]
Wrong tape splicing due to incorrect tape reel splicing.
[Measures]
Splice the vinyl using the vinyl splicing tape and splicing tip provided by Hanwha
Precision Machinery Co., Ltd. and splice the tape reel again properly. (Refer to the
tape feeder manual)
E0124 The Y part feeding position is incorrect when installing tape
[Cause]
The Y coordinate for pickup has deviated since there is a part or foreign material on
the reference surface of the tape feeder.
1-16
Next Generation, Multi-Functional Placer DECAN S1 Troubleshooting Guide
[Measures]
Remove the part or foreign materials.
E0125 The X part feeding position is incorrect due to a problem with the feeder
[Cause]
Incorrect X pickup position of the tape feeder
[Measures]
Adjust the X pickup position of the tape feeder using the calibration jig provided by
Hanwha Precision Machinery Co., Ltd..
E0126 Incorrect setup of the part feeding position of the feeder
[Cause]
The pickup position of the tape feeder does not match with the '-' marked position of
the tape guide.
[Measures]
Calibrate the position using the calibration jig provided by Hanwha Precision
Machinery Co., Ltd..
E0127 Deformed vertical position of the feeder
[Cause]
The position setting pin of the feeder base is worn or there are foreign materials in the
hole into which the position setting pin or the feeder base position setting pin is
inserted
[Measures]
When removing foreign materials or replacing the worn part, contact our designated
C/S company or local agent for proper measures. (Replace the position setting pin)
E0128 Incorrect part feeding position due to worn or deformed feeder parts
[Cause]
1) Distorted eccentric pin setting the position of the sprocket.
2) Parts of ratchet, stop pawl, etc. are worn out.
[Measures]
1) Calibrate the position using the calibration jig provided by Hanwha Precision
Machinery Co., Ltd..
2) ontact our designated C/S company or local agent for proper measures.
E0129 Incorrect part feeding position due to foreign materials on the sprocket, ratchet, etc.
[Cause]
1-17
System Messages of the MMI and Solutions
Foreign materials on the sprocket, ratchet, etc.
[Measures]
Clean the sprocket, ratchet, etc. periodically.
E0130 Incorrect setup of the part supply position according to tray shape and part
characteristics
[Cause]
1) Defective part pickup according to the tray for odd shaped parts
2) Limitation of the part pickup of the gripper according to the position of the odd shaped
tray part (center, edge)
[Measures]
1) Clean the sprocket, ratchet, etc. periodically.
2) Check the shape of the odd-shaped tray and gripper stroke and replace the gripper with
an appropriate one
E0131 Incorrect setup of Z and Pick Z values
[Cause]
1) The user entered an incorrect part thickness.
2) The user entered an incorrect Z value when entering the feeder pickup point.
3) For parts fed by the tray feeder, the Pick Z value is set incorrectly
[Measures]
1) Input the height of the part measure using vernier calipers.
2) In the case of the tape reel, the Z value is a positive (+) value. Usually, set the value so
that it becomes less than the usual part thickness by 0.1~0.2 mm. In the case of the
embossed reel, set a negative (-) Z value to -0.1.
3) Teach the Pickup Z value manually and input the correct value.
E0132 Foreign materials on the feeder base slot and clamp
[Cause]
There are foreign materials in the feeder base slot or clamp.
[Measures]
Remove foreign materials, if any, and clean the feeder base periodically.
E0133 Incorrect Z offset setup
[Cause]
The Z axis offset has been set up incorrectly
[Measures]