Autosite_Users_Manual - 第25页
Setup an d Installa tion AutoSite User Manual 2-3 Figure 2-1 Flowchart of the Installation Proces s for the P roMaster 2000 START CONVERT CONTACTOR SET ? MOUNTING BRACKETS ALREADY ON PIN HEAD DRIVER? REMOVE CONTACTOR SET…
Setup and Installation
2-2 AutoSite User Manual
Before You Begin
Before you begin the setup and installation, make sure you read and
understand the terms of the Software License Agreement, which is
printed on the outside of the envelope containing the AutoSite disks.
Connect AutoSite to a ProMaster 2000
This section describes how to connect AutoSite to a ProMaster 2000
handler. The installation is divided into two main steps:
• Attach the AutoSite control unit to the 2000
• Attach the AutoSite pin driver head to the 2000
Figure 2-1 is a flowchart that illustrates the general flow of the installation
procedures contained in this section.
What You Need
In addition to the contents of the Installation Kit, you will need the
following to connect AutoSite to a ProMaster 2000:
•Programming module
• Grounded wrist strap
• Antistatic workstation
• 5/32-inch hex driver
• Flatblade screwdriver
• #2 Phillips screwdriver
Safety Information
This information is provided as a supplement to the Safety Summary at
the beginning of this manual.
The circuitry housed inside the pin driver head and the control unit and
the devices AutoSite programs are static sensitive and can be damaged by
electrostatic discharge (ESD). To help minimize the effects of ESD, we
suggest you wear an antistatic wrist strap while you follow the
procedures described in this section.
For best performance, the antistatic wrist strap should be connected to a
properly grounded antistatic workstation and the wrist strap should
contain a 1M
Ω
(minimum) to 10M
Ω
(maximum) isolating resistor.
Setup and Installation
AutoSite User Manual 2-3
Figure 2-1
Flowchart of the Installation
Process for the ProMaster 2000
START
CONVERT
CONTACTOR
SET ?
MOUNTING
BRACKETS
ALREADY ON PIN
HEAD DRIVER?
REMOVE CONTACTOR
SET FROM HANDLER
ATTACH MOUNTING
BRACKETS TO
PIN DRIVER HEAD
Y
N
N
Y
ATTACH PROGRAMMING
MODULE TO PIN
DRIVER HEAD
ATTACH PIN DRIVER
HEAD TO 2000
FINISH
1415-2
ATTACH CONTROL UNIT
TO PROMASTER 2000
REMOVE CONTACTOR
SET FROM SMALL PLATE
FASTEN CONTACTOR
SET TO MOUNTING PLATE
ATTACH CONTACTOR
SET AND MOUNTING
PLATE TO 2000
Setup and Installation
2-4 AutoSite User Manual
Attaching the
Control Unit
Connect the AutoSite control unit to a ProMaster 2000 as follows:
1. Unplug the power cord from the AutoSite control unit.
2.
(For control units without connector brackets at ports J1 and J2)
Make sure
the 50-pin cable and the 68-pin cable are disconnected from the
control unit and the pin driver head. The cables and the ports to
which they connect are shown in Figures 1-1 and 1-3.
(For control units with connector brackets at ports J1 and J2)
Make sure
the 50-pin cable and the 68-pin cable are disconnected from the pin
driver head.
3. Locate the two flathead screws shown in Figure 2-2 and remove them
from the control unit. Set these screws aside; you will need them
later.
4. As shown in Figure 2-2, position the control unit mounting plate
against the control unit so the countersunk holes on the control unit
mounting plate are facing away from the control unit. Also, make
sure that the narrow end of the control unit mounting plate is
pointing toward the disk drive on the control unit.
Secure the control unit mounting plate to the control unit with the
two flathead screws you removed in step 3. Tighten the screws with a
#2 Phillips screwdriver. Do not overtighten the screws.
Figure 2-2
Attaching the Control Unit
Mounting Plate to the Control Unit
1344-1
SCREWS
BEVELED
EDGE
CONTROL UNIT
MOUNTING PLATE
CONTROL UNIT