Autosite_Users_Manual - 第82页

Operation 3-24 AutoSite User Manual 11. Select the test mode. You can select either one-pass or continuous testing. To tog gle modes, move the curs or to the Test Mode field an d press S PACE . One Pass testing run s the…

Operation

AutoSite User Manual 3-23

8. Make sure the device socket is empty.

9. If you are using TaskLink, select

Programmer Interface

from the

Utilities

menu.

10. From the Main Menu, press

to display the Self-test screen,

which is shown in Figure 3-16.

Note: The

Base/Adapter/Relays

field will display

????

if this test has not

explicitly been run from the Self-test screen for the current base. The

Base/Adapter/Relay test is not run during powerup self-test.

In addition, the screen shown above may differ slightly from the screen

shown on your terminal.

Figure 3-15

The AutoSite Main Menu

Figure 3-16

The Self-test Screen

Operation

3-24 AutoSite User Manual

11. Select the test mode. You can select either one-pass or continuous

testing. To toggle modes, move the cursor to the Test Mode field and

press

PACE

One Pass testing runs the specified test once. Continuous testing runs

the specified test until there is a failure or until you stop the test by

pressing

TRL

Note: There may be a delay before AutoSite responds to the Ctrl-Z if you are

testing system RAM or user RAM.

CAUTION: Executing the System RAM test or the User RAM test erases

all data in RAM.

12. To test all hardware, move the cursor to the

Perform All Tests

prompt and press

↵

. To test a particular item, move the cursor to the

desired test and press

↵

Manipulating Keep Current Algorithm Files

The Keep Current service allows you to download new and updated

device algorithms from the Keep Current Bulletin Board System. Keep

Current algorithms are made available to Keep Current subscribers

before they are incorporated in an update kit.

See the

Keep Current User Manual

for more information and for

instructions on downloading Keep Current algorithms.

Accessing the Keep

Current Menu

Before you can manipulate a Keep Current algorithm file, you must

access the Keep Current menu, which can only be done with a full screen

terminal that emulates one of the following:

• ANSI 3.64 compatible terminals

• DEC VT-100 compatible terminals (supported by TaskLink)

• Qume QVT-101 compatible terminals

• TELEVIDEO TVI--910 compatible terminals

• Wyse WY-30 compatible terminals

If you are using handler control software, consult the documentation to

see if it supports one of the terminal types listed above.

Operation

AutoSite User Manual 3-25

If you are using TaskLink, your system should already be configured to

access the Keep Current menu; skip to step 9 on the next page. Otherwise,

do the following:

1. Connect the terminal to one of the serial ports on the control unit. The

serial ports are shown in Figure 1-4.

2. Configure your terminal or terminal emulation software to match the

following parameters:

• 9600 baud

•No parity

• 8 data bits

•1 stop bit

See the documentation supplied with your terminal or terminal

emulation software for more information.

3. Power up AutoSite if it is not already powered up. If you power up

AutoSite, wait for AutoSite to complete the powerup self-test. The

self-test LED on the control unit goes out when the self-test is

complete.

Note: The powerup self-test takes approximately three minutes on a 44-pin

AutoSite and four minutes on an 88-pin AutoSite.

4. When the self-test is complete, you will see either the powerup screen

or a single angle bracket prompt (

. If you see the powerup screen,

go to step 6.

5. Type

↵

to display the powerup screen.

6. AutoSite displays the powerup screen and the following prompt:

Current terminal type = DEC VT100 (ANSI 3.64)

Do you want to select a new terminal type? (Y/N)

If the current terminal type matches the terminal type you are using,

press

↵

and go to step 8.

If the current terminal type does not match the terminal type you are

using, press

↵

. AutoSite displays the default and current terminal

types and a list of the available terminal types. Select a terminal type

that matches the terminal you are using and press

↵

7. AutoSite responds with the following prompt:

Save terminal type as power on default? (Y/N)

Press

↵

. AutoSite saves your current terminal type as the power on

default and then displays the Main Menu, which is shown in

Figure 3-15.

8. From the Main Menu, press

to get to the Keep Current menu.