00197467-01_SM_DLM3-4_Kunde_en - 第28页
Service Work Replacing the DP Rocker 28 Service Manual SIPLACE Placement Heads DLM3/DLM4 Preparation ► Remove the head from the machine. For details about removing an d fitting the placement head, refer to the service ma…
Service Work
Replacing the DP Rocker
Service Manual SIPLACE Placement Heads DLM3/DLM4 27
3.6
3.6 Replacing the DP Rocker
Replacing the DP Rocker
Parts, equipment and tools
▪ Upper section of rocker assembly / R2 [03065216Sxx]
▪ Belt tensioning device DP-DLM [03063649-xx]
▪ Tool kit for RF rocker, turning station DLM [03064145-xx] (contains the "upper section of rocker as
-
sembly / R2" [03065216Sxx])
Overview
NOTICE
Improvement
The swivel-in rocker of the DP station has been fitted with 2 cones from version 7 onwards. The
DP station [00320041-05] can be upgraded to accommodate this improvement by simply re
-
placing the old part.
1. Fastening screws for rocker arm
(screwdriver, size 0).
2. Drive wheel
3. Drive arm
NOTICE!
The rocker arm is located under the drive arm (3). The
drive arm is fixed to the rocker arm with the two screws
(1).
The adjacent diagram shows a comparison of the spring
mechanism on the DP rocker with version 5 (1) and ver
-
sion 7 (2) with two cones.
Service Work
Replacing the DP Rocker
28 Service Manual SIPLACE Placement Heads DLM3/DLM4
Preparation
► Remove the head from the machine. For details about removing and fitting the placement head, refer
to the service manual for your machine.
Removal
► Loosen the two fastening screws (size 0 screwdriver).
► You can now move the rocker and pull off the belt.
► Swing the rocker arm on the motor to one side and remove the rocker arm with drive wheel from the
swivel-in ball bearing.
Installation
► Fit the drive armwith drive wheel back on the swivel-in ball bearing.
► Swivel the rocker arm on the motor back and refit the M2x3.5 screws.
► See also "3.7 Replacing the Toothed Belt for the DLM Turning Station (from version 07) [00320041-
xx]" [ ➙ 29] for the following tasks.
► Place the belt back on the drive wheel and pull it over the motor toothed wheel.
► Fit the belt tensioning device for the DP station.
► Tighten the two screws.
► Further installation is performed by following the above instructions in the reverse order.
NOTICE
Replacing the DP rocker
When replacing the DP rocker, you also need to replace the drive toothed belt.
Service Work
Replacing the Toothed Belt for the DLM Turning Station (from version 07)
Service Manual SIPLACE Placement Heads DLM3/DLM4 29
3.7
3.7 Replacing the Toothed Belt for the DLM Turning Station (from version 07) [00320041-xx]
Replacing the Toothed Belt for the DLM Turning Station (from
version 07) [00320041-xx]
Parts, equipment and tools
Preparation
► Remove the head from the machine. For details about removing and fitting the placement head, refer
to the service manual for your machine.
Removal/installation
► Further installation is performed by following the above instructions in the reverse order. Also ob
-
serve the following instructions:
Belt tensioning device for turning station DLM
▪ Belt tensioning device for turning station DLM
[03063649
-
xx]
▪ Lubricant Isoflex Topas NCA52
▪ Synchroflex toothed belt 2.5 T2/90 [00320041
-
xx]
► Remove the turning station (see "3.5 Replacing the
Turning Station" [ ➙ 25]).
NOTICE!
To loosen or tighten the fastening screw on the rocker,
hold the DP station between your thumb and index finger
so that the swivel-in rocker (1) can be moved to the left
and right.
► Remove the defective toothed belt.
► Loosen the two fastening screws (3) with a size 0
screwdriver. Do not fully remove the screws (leave
them in the unit).
► Grease the new toothed belt slightly with Isoflex
Topas NCA52.
► Fit the new toothed belt onto the toothed wheels.
► Fit the adjustment aid (2) between the motor drive
toothed wheel (4) and the sleeve drive wheel (5). The
tension of the steel spring in the tool sets the belt to
the correct tension.
► Now tighten the two screws fastening (3) the rocker
with a size 0 screwdriver.
NOTICE
Installation instructions
► Check the axis dynamics. Read the service manual or settings manual for your machine
first.