00197467-01_SM_DLM3-4_Kunde_en - 第63页
Measuring Equipment and Tools Z Axis Gauge (Old) [00331308-xx] Service Manual SIPLACE Placement Heads DLM3/DLM4 63 4 4 M e a s u r in g E q u ip m e n t a n d T o o ls Measuring Equipment and Tools 4.1 4 . 1 Z A x is G a…
Service Work
Replacing the Vacuum Hoses on the Head 3.17.3 Replacing the Silicone Hoses on the Star [00341183S01]
62 Service Manual SIPLACE Placement Heads DLM3/DLM4
3.23
3.23 Replacing the Vacuum Hoses on the Head
Replacing the Vacuum Hoses on the Head
The length of the vacuum hoses and the way in which they are fitted has been improved to ensure that,
when the hoses are replaced - especially in SX, DX, X, D3 and HF machines - these hoses can be run
in a manner which will not interrupt the vacuum supply.
Parts, equipment and tools
▪ Vacuum hoses and guidance [03064147-xx]
Contents:
– Hose for placement circuit query (new length: 180 mm, old length: 190 mm) [03002187-02]
– Hose for holding circuit query (new length: 225 mm, old length: 200 mm) [03002188-02]
– Hose for placement circuit / 3x6x145 (new length: 145 mm, old length: 125 mm) [03010444-02]
– Hose for hold circuit / 4x7x140 [03010445S01]
– Hose guide [03048807-01]
– Cylinder screw M3x6 DIN912-A2 [03045028-01]
Preparation
► Remove the head from the machine. For details about removing and fitting the placement head, refer
to the service manual for your machine.
Removal
► Disconnect the hoses from the vacuum generator and the vacuum measuring board.
Installation
► Fit the additional hose guide (M3 screw) on the top measuring hose duct.
► Fit the new hose as shown in the diagrams.
► Further installation is performed by following the above instructions in the reverse order.
CAUTION
Mark the connection points and the route of the hoses
Mark the connection points and the route of the individual hoses, so that these can be rerun
correctly later on.
Measuring Equipment and Tools
Z Axis Gauge (Old) [00331308-xx]
Service Manual SIPLACE Placement Heads DLM3/DLM4 63
4
4 Measuring Equipment and Tools
Measuring Equipment and Tools
4.1
4.1 Z Axis Gauge (Old) [00331308-xx]
Z Axis Gauge (Old) [00331308-xx]
4.2
4.2 RC Filter [02102858-xx]
RC Filter [02102858-xx]
4.3
4.3 Calibration Tool [03010565-xx]
Calibration Tool [03010565-xx]
Use:
The gauge is used to set the top Z axis stopper.
Use:
The RC filter is used for setting the axis dynamics.
Use:
The calibration tool [03010565-xx] is used for calibration
of the DLM, CPP, P&P heads, TwinHead and PCB cam
-
era.
Measuring Equipment and Tools
Calibration Tools for Vision Systems
64 Service Manual SIPLACE Placement Heads DLM3/DLM4
4.4
4.4 Calibration Tools for Vision Systems
Calibration Tools for Vision Systems
4.5
4.5 Z End Stopper Star Gauge for C&P6/12 [03019865-xx]
Z End Stopper Star Gauge for C&P6/12 [03019865-xx]
4.6
4.6 Power Pack for Star Installation
Power Pack for Star Installation
Use:
▪ C&P6/12head on the D, X and HF series:
Calibration tool [03010565-xx]
▪ C&P20 head on the X-Series (for component camera
type 23):
Calibration tool [03034148-xx]
▪ Machines with 4xx software:
Calibration tool [00316308-xx] (version II, transpar
-
ent)
Use:
The gauge is used to set the end stop position of the C&P
head Z axis.
Use:
The power pack is used as an adjustment aid for installa
-
tion of the star on C&P6/12 heads.