Transport Rails Module.pdf - 第22页

TRANSPORT RAILS MODULE ADJUSTMENTS AND SETTINGS 16.22 Technical Reference Manu al Chapter Issue 4 Jan 10 6. Slacken the two rear snugger plate securing scre ws. 7. Place a product board centrally between the snugge rs. 8…

100%1 / 44
TRANSPORT RAILS MODULE
ADJUSTMENTS AND SETTINGS
Chapter Issue 4 Jan 10 Technical Reference Manual 16.21
14. Select Run Diagnost.
15. Open the front printhead cover.
16. Adjust the two downstop screws on the snugger base plate so that the top
of the board and the rear snugger plate are aligned.
17. Adjust the two downstop screws on the front snugger plate so that the top
of the board and the front snugger plate are aligned.
18. Close the front printhead cover.
19. Press the System button.
20. Select Toggle Board Clamp.
21. Select Run Diagnost.
22. Open the front printhead cover.
23. Remove the product board from the machine.
24. Refit the screen.
25. Close the front printhead cover.
26. Press the System button.
27. Select Exit.
28. Select Exit.
29. Select Back.
Rear Snugger
Plate Parallelism
1. Select Open Cover Commands.
2. Select Carriage To Rear.
3. Select Unload Screen.
4. Open the front printhead cover.
5. Remove the screen from the machine.
Downstop Screws
Downstop Screws
Rear Snugger Plate
Front Snugger Plate
Plan View of Rail System
Snugger Base Plate
TRANSPORT RAILS MODULE
ADJUSTMENTS AND SETTINGS
16.22 Technical Reference Manual Chapter Issue 4 Jan 10
6. Slacken the two rear snugger plate securing screws.
7. Place a product board centrally between the snuggers.
8. Close the front printhead cover.
9. Press the System button.
10. Select Maintenance.
11. Select Diagnostics.
12. Use Next or Previous to highlight Rail System.
13. Select Select Module.
14. Use Next or Previous to highlight Toggle Board Clamp.
15. Select Run Diagnost.
16. The edge of the rear snugger plate aligns with the edge of the board.
17. Open the front printhead cover.
18. Tighten the two rear snugger plate securing screws.
19. Close the front printhead cover.
20. Press the System button.
21. Select Run Diagnost.
22. Open the front printhead cover.
23. Remove the product board from the machine.
24. Refit the screen.
25. Close the front printhead cover.
26. Press the System button.
27. Select Exit.
28. Select Exit.
29. Select Back.
Home Position
Rail Width Check
Ensure that the board clamps are fitted and that the Board Clamp Setting
procedure (this section refers) has been completed before carrying out the
following procedure:
1. Select Open Cover Commands.
Downstop Screws
Downstop Screws
Rear Snugger Plate Rear Snugger Plate Securing Screws
Plan View of Rail System
TRANSPORT RAILS MODULE
ADJUSTMENTS AND SETTINGS
Chapter Issue 4 Jan 10 Technical Reference Manual 16.23
2. Select Carriage To Rear.
3. Select Unload Screen.
4. Open the front printhead cover.
5. Remove the screen from the machine.
6. Close the front printhead cover.
7. Press the System button.
8. Select Maintenance.
9. Select Diagnostics.
10. Use Next or Previous to highlight Rail System.
11. Select Select Module.
12. Ensure that Home Rail Width is highlighted.
13. Select Run Diagnost.
14. Select Adjust and set the board width to 250mm.
15. Select Exit.
16. Use Next or Previous to highlight Drive Rail to Board Width.
17. Select Run Diagnost.
18. Open the front printhead cover.
19. Place a vernier gauge above the transport belts in the centre of the board
clamps and check that the vernier reads 250.25mm ±0.10mm.
20. If the rail width is correct, go to Step 30.
21. Close the front printhead cover.
22. Press the System button.
23. Use Next or Previous to highlight Set Rail Board Width Calibration.
24. Select Run Diagnost to open the Rail Width Offset window.
250.25mm ±0.10mm
Rear Board Clamp
Plan View of Board Clamps
Transport Belts
Front Board Clamp